Re: Making a punch die?
Posted by
Joseph
on 2001-07-13 00:00:19 UTC
Thanks Bob.
Yes, I agree, the nibbling tools from Radio Shack are terrific and
convenient; although my hands get very sore after biting away a large
cutout. The only problems is that the results (from my unsteady
impatient hands) don't have a nice clean fit that I would get from
dies.
Joseph
Yes, I agree, the nibbling tools from Radio Shack are terrific and
convenient; although my hands get very sore after biting away a large
cutout. The only problems is that the results (from my unsteady
impatient hands) don't have a nice clean fit that I would get from
dies.
Joseph
--- In CAD_CAM_EDM_DRO@y..., cncdxf@a... wrote:
> Hi Joseph,
> Years ago I bought GREELEE punch and die sets for
> doing chassis cuts outs. I found a NIBBLING tool at Radio Shack
> that was more flexable. Most cabinets are stamped then folded so if
> if you use a NIBBLING tool you will have to put your outline on the
> inside of the chassis. Radio Shack still sells a NIBBLING tool for
> $9.99. Ignore this message if you own one.
>
> Nibbling Bob
>
>
> --- In CAD_CAM_EDM_DRO@y..., "Joseph" <toybuilder@y...> wrote:
> > Hi,
> > I'd like to make my own punch dies for cutting cutouts for
> electronic
> > connectors in an aluminum case (0.062). Has anyone tried this or
> > seen information that might help?
> > Joseph
Discussion Thread
Joseph
2001-07-12 13:03:04 UTC
Making a punch die?
Alan Marconett KM6VV
2001-07-12 13:36:56 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
Joseph
2001-07-12 15:04:50 UTC
Re: Making a punch die?
Alan Marconett KM6VV
2001-07-12 15:26:41 UTC
Re: Making a punch die?
Spehro Pefhany
2001-07-12 15:43:10 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
cncdxf@a...
2001-07-12 15:48:14 UTC
Re: Making a punch die?
lew best
2001-07-12 16:14:10 UTC
RE: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Alan Marconett KM6VV
2001-07-12 16:21:37 UTC
Re: Making a punch die?
Jon Elson
2001-07-12 20:04:44 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
Smoke
2001-07-12 20:05:25 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
Smoke
2001-07-12 20:07:53 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
Jon Elson
2001-07-12 20:17:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Jon Elson
2001-07-12 20:22:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Sven Peter, TAD S.A.
2001-07-12 21:10:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Joseph
2001-07-12 23:46:14 UTC
Re: Making a punch die?
Joseph
2001-07-13 00:00:19 UTC
Re: Making a punch die?
ptengin@a...
2001-07-13 00:23:31 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
Ian Wright
2001-07-13 02:00:28 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
machines@n...
2001-07-13 03:04:44 UTC
Re: Making a punch die?
Ian Wright
2001-07-13 06:29:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Fred Smith
2001-07-13 06:56:11 UTC
Re: Making a punch die?
Dan Mauch
2001-07-13 06:57:17 UTC
RE: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Alan Marconett KM6VV
2001-07-13 09:21:01 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
Alan Marconett KM6VV
2001-07-13 09:37:17 UTC
Re: Making a punch die?
mdickey@b...
2001-07-13 10:08:47 UTC
Re: Making a punch die?
Jon Elson
2001-07-13 10:43:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Ron Yost
2001-07-13 10:54:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Smoke
2001-07-13 13:42:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Spehro Pefhany
2001-07-13 13:53:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Alan Marconett KM6VV
2001-07-13 17:18:57 UTC
Re: Making a punch die?
Joseph
2001-07-13 18:57:41 UTC
Re: Making a punch die?
lew best
2001-07-13 19:13:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: Making a punch die?
IMService
2001-07-14 06:02:25 UTC
Re:Re: Making a punch die?
Dan Mauch
2001-07-14 08:27:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: Making a punch die?
diazden
2001-07-14 18:20:22 UTC
Re: [CAD_CAM_EDM_DRO] Making a punch die?
diazden
2001-07-14 18:20:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Making a punch die?
Alan Marconett KM6VV
2001-07-14 19:14:42 UTC
Re: Making a punch die?