CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] EMC Encoders

on 2001-08-03 10:17:54 UTC
There are boards out there with ISA slots
I just bought a Soyo Socket 7 board from
Tiger Direct for about $69.00 and
an AMD 450 I got off ebay for $23.00
The board has 3 ISA slots, baby AT size.
EMC BDI loaded up fine with this board.

32meg memory - (had it laying around)
Vodoo3 1000 video board (found that on an airplane)
old 486 case, power supply, 1.6 gig hard drive, 4X CD ($8.00 Surplus)
14" SVGA monitor ($8.00 from the rescue mission store)
CPU Fan ($6.00 tiger direct)
EMC BDI ($10.00)

Total Cost less than $150.00 for a controller
that does 300ipm rapids Not too bad :)

Bill

>
>
> > -----Original Message-----
> > Thanks for the info.
> >
> > Questions:
> >
> > When will your board be ready?
> >
> > If I buy a new computer can I get an ISA slot?
>
> I know that some motherboard makers are still offering 1 ISA slot with
> current processors.
>
> > What is the highest # of steps per second that EMC will
> > support? I read in
> > the Aug 11, 2000 release notes that it was 5,000, but that
> > was dated July
> > 14, 1999.
>
> I have run up to 28,000 using steppermod. Don't know if Freqmod (the
> basis for smdromod) is up to that high a step rate. If it is you will
> need a fast computer.
>
> > What would be the maximum on your board?
> >
> > I have an existing machine with 1000 step/rev motors and 4
> > rev/inch lead
> > screws. The limit of the lead screws is 10 inches per second
> > which would be
> > 40,000 steps/sec. If none of the above work, what's the next step?
>
> For steppers than Gecko G210a. They are pulse multipliers so you
> actually drive them at a lower rate.
>
> Tim
> [Denver, CO]
>

Discussion Thread

Ethan Vos 2001-08-01 11:46:50 UTC EMC Encoders Tim 2001-08-01 13:31:52 UTC RE: [CAD_CAM_EDM_DRO] EMC Encoders Jon Elson 2001-08-01 20:26:20 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders Ethan Vos 2001-08-02 04:23:19 UTC RE: [CAD_CAM_EDM_DRO] EMC Encoders Jon Elson 2001-08-02 10:03:23 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders Ethan Vos 2001-08-02 10:30:43 UTC RE: [CAD_CAM_EDM_DRO] EMC Encoders Tim 2001-08-02 15:50:03 UTC RE: [CAD_CAM_EDM_DRO] EMC Encoders Tim 2001-08-02 15:50:04 UTC RE: [CAD_CAM_EDM_DRO] EMC Encoders Jon Elson 2001-08-02 20:33:10 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders William Scalione 2001-08-03 10:17:54 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders Paul 2001-08-03 11:47:18 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders William Scalione 2001-08-03 17:26:10 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders Jon Elson 2001-08-03 22:28:41 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders William Scalione 2001-08-03 22:58:47 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders Paul 2001-08-04 04:12:45 UTC Re: [CAD_CAM_EDM_DRO] EMC Encoders Ray 2001-08-04 10:13:23 UTC Re: Re: EMC Encoders Ray 2001-08-04 19:09:46 UTC Re: Re: EMC Encoders Granola@v... 2001-08-05 05:22:44 UTC Re: EMC Encoders