Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
Posted by
Don Carlson
on 2001-08-27 13:09:10 UTC
The port assignment is ECP. By the way, I can change the port assignment to
another port, ie, 378 or 278. and after rebooting to make it effective,
start CNCpro and works ok again until the next reboot. So the port
assignment does not to seem to have any effect on the problem.
The curious thing, is that DeskNC works without a flaw. I believe there is
something queer in the CNCpro setup
thanks, Don
At 11:02 AM 8/27/2001 -0400, you wrote:
another port, ie, 378 or 278. and after rebooting to make it effective,
start CNCpro and works ok again until the next reboot. So the port
assignment does not to seem to have any effect on the problem.
The curious thing, is that DeskNC works without a flaw. I believe there is
something queer in the CNCpro setup
thanks, Don
At 11:02 AM 8/27/2001 -0400, you wrote:
>Don: I am using a ThinkPad 760XD with CNCPro to run my Hardinge lathe
>conversion. I seem to recall some initial problems that were rectified
>by going into the ThinkPad features and going to the parallel port
>advanced setup and changing to ECP. Carey
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
Don Carlson
2001-08-27 07:42:04 UTC
CNCpro Parallel port problem
Carey L. Culpepper
2001-08-27 08:17:43 UTC
Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
William Scalione
2001-08-27 08:41:16 UTC
Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
Jon Elson
2001-08-27 11:40:16 UTC
Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
vrsculptor@h...
2001-08-27 12:10:32 UTC
Re: CNCpro Parallel port problem
Don Carlson
2001-08-27 13:02:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCpro Parallel port problem
Don Carlson
2001-08-27 13:02:52 UTC
Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
Don Carlson
2001-08-27 13:04:05 UTC
Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
Don Carlson
2001-08-27 13:09:10 UTC
Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
Alan Marconett KM6VV
2001-08-27 13:38:56 UTC
Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
Alan Rothenbush
2001-08-27 14:19:43 UTC
Re: CNCpro Parallel port problem
cnc002@a...
2001-08-28 08:15:44 UTC
Re: [CAD_CAM_EDM_DRO] CNCpro Parallel port problem
cnc002@a...
2001-08-28 08:19:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCpro Parallel port problem
Tom Eldredge
2001-08-31 14:51:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: CNCpro Parallel port problem