Re: [CAD_CAM_EDM_DRO] linear encoder to control rotary indexer??

I found it hiding out on this group's files section. Here it is, don't
forget to copy ALL of the address:

http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/Rifling%20Machine/

John H.

> I believe you posted that to the Lathe 2000 group??? but don't quote me on
> that ;)
>
> Bryan
>
> -----Original Message-----
> From: Smoke [mailto:gordonr@...]
> Sent: Wednesday, 29 August, 2001 11:03 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: Re: [CAD_CAM_EDM_DRO] linear encoder to control rotary
> indexer??
>
>
> As a gunsmith and machine retired machine designer, methinks it would be
> much easier and cheaper to build your machine so as to contol the lead
> mechanically rather than electronically. This would also guarantee
> following the reverse path exactly as well as eliminate the need for a
> computer or any programming. All you'd need in the way of electronics

would

> be an on/off switch and a couple of limit switches for travel.
>
>
> I posted a design someplace earlier this year (don't remember exactly

which

> site I posted it on) for an attachment that could be mounted on a standard
> lathe for building a rifiling machine.
>
> Smoke
>
>
> >I am trying to build a rifling machine. I was planning on using the

indexer

> >to rotate the cutter as it's pulled though the barrel. So if I could just
> >make the indexer rotate at the desired rate as it's moved along it should
> >work. It would also need to be able to follow the exact path in reverse.
> >Thanks, Brad
> >
> >>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>