Re: [CAD_CAM_EDM_DRO] Re: Stepper size?

Hi all
can u send it as attachment at my yahoo address???


shabbir
shabbr_2000@...


At 01:39 PM 9/27/01 +0000, you wrote:

>It was free to download and use, not even a copyright notice.
>
>It's about 700k zipped. Can upload it but isn't "files" full.
>
>Or can E-mail it.
>
>
>--- In CAD_CAM_EDM_DRO@y..., dlantz@a... wrote:
>> is it a freeware programs? can you share it with us? that would be
>> great!---Dave L.
>>
>> -----Original Message-----
>> From: shymu@b... [mailto:shymu@b...]
>> Sent: Thursday, September 27, 2001 6:27 AM
>> To: CAD_CAM_EDM_DRO@y...
>> Subject: [CAD_CAM_EDM_DRO] Re: Stepper size?
>>
>>
>> I have a program that calculates servo/stepper size based on load,
>> ramp speed, screw pitch/type, slide type, etc. And outputs are data
>> and graphs showing torque needed. Data entry is easy with great help
>> files. Very usefull !
>>
>>
>>
>> --- In CAD_CAM_EDM_DRO@y..., zbadone@b... wrote:
>> > I am in the process of designing my XYZ table. I am interested in
>> > routing machinable wax for use with my casting furnace, light wood
>> > routing and perhaps (light) engraving aluminum. Not very deep cuts
>> in
>> > the aluminum.
>> >
>> > I am trying to figure out a decent size stepper motor to use. I
>came
>> > accross a few on the net in the 125 oz/in model, one is a Size 23
>> > ($40)Vexta PK226-02A, 200 s/r 3.6v@2A
>> > and the other is a Size 34 ($25 used)125oz 2.5v@2... 200 s/r(steps
>> per
>> > rev).
>> >
>> > My table is what will be moving, made out of 3/4" cabinet grade
>ply,
>> > 24" * 30". What would be the recommended size based on my
>> application?
>> >
>> > The over head gantry will house a Dewalt 1/4" laminat trimmer, not
>> > much weight.
>> >
>> > Anybody have an opinion on these types of stepper or do you have
>> > another source I could look at?
>> >
>> > Thanks.
>>
>>
>> Addresses:
>> FAQ: http://www.ktmarketing.com/faq.html
>> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>>
>> Post messages: CAD_CAM_EDM_DRO@y...
>> Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
>> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
>> List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
>> Moderator: jmelson@a... timg@k... [Moderator]
>> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>> bill,
>> List Manager
>>
>>
>>
>> Your use of Yahoo! Groups is subject to
>http://docs.yahoo.com/info/terms/
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>