Re: Stepper size software download link?

Sorry about that,... the install file is 2 meg not 700k.

Go here to download direct. The file is Camas.exe

http://www.electrosales.com/warner/software/


Frank

--- In CAD_CAM_EDM_DRO@y..., "Lew Best" <bcl@c...> wrote:
> Looks like there's about 3400k space available if I read it
correctly. If
> you can't upload it I'd like a copy at bcl@c...
>
> Thanks!
>
> Lew
>
> -----Original Message-----
> From: shymu@b... [mailto:shymu@b...]
> Sent: Thursday, September 27, 2001 8:39 AM
> To: CAD_CAM_EDM_DRO@y...
> Subject: [CAD_CAM_EDM_DRO] Re: Stepper size?
>
> It was free to download and use, not even a copyright notice.
>
> It's about 700k zipped. Can upload it but isn't "files" full.
>
> Or can E-mail it.
>
>
> --- In CAD_CAM_EDM_DRO@y..., dlantz@a... wrote:
> > is it a freeware programs? can you share it with us? that would
be
> > great!---Dave L.
> >
> > -----Original Message-----
> > From: shymu@b... [mailto:shymu@b...]
> > Sent: Thursday, September 27, 2001 6:27 AM
> > To: CAD_CAM_EDM_DRO@y...
> > Subject: [CAD_CAM_EDM_DRO] Re: Stepper size?
> >
> >
> > I have a program that calculates servo/stepper size based on load,
> > ramp speed, screw pitch/type, slide type, etc. And outputs are
data
> > and graphs showing torque needed. Data entry is easy with great
help
> > files. Very usefull !
> >
> >
> >
> > --- In CAD_CAM_EDM_DRO@y..., zbadone@b... wrote:
> > > I am in the process of designing my XYZ table. I am interested
in
> > > routing machinable wax for use with my casting furnace, light
wood
> > > routing and perhaps (light) engraving aluminum. Not very deep
cuts
> > in
> > > the aluminum.
> > >
> > > I am trying to figure out a decent size stepper motor to use. I
> came
> > > accross a few on the net in the 125 oz/in model, one is a Size
23
> > > ($40)Vexta PK226-02A, 200 s/r 3.6v@2A
> > > and the other is a Size 34 ($25 used)125oz 2.5v@2... 200
s/r(steps
> > per
> > > rev).
> > >
> > > My table is what will be moving, made out of 3/4" cabinet grade
> ply,
> > > 24" * 30". What would be the recommended size based on my
> > application?
> > >
> > > The over head gantry will house a Dewalt 1/4" laminat trimmer,
not
> > > much weight.
> > >
> > > Anybody have an opinion on these types of stepper or do you have
> > > another source I could look at?
> > >
> > > Thanks.
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> > Post messages: CAD_CAM_EDM_DRO@y...
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > Moderator: jmelson@a... timg@k... [Moderator]
> > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > bill,
> > List Manager
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@y...
> Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> Moderator: jmelson@a... timg@k... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/