Re: [CAD_CAM_EDM_DRO] Re: Stepper size?

Would you be able to email that to me please if the files section is full
up? My email is johnhe@...

Thanks,
John He.

> >It's about 700k zipped. Can upload it but isn't "files" full.
> >
> >Or can E-mail it.
> >
> >
> >--- In CAD_CAM_EDM_DRO@y..., dlantz@a... wrote:
> >> is it a freeware programs? can you share it with us? that would be
> >> great!---Dave L.
> >>
> >> -----Original Message-----
> >> From: shymu@b... [mailto:shymu@b...]
> >> Sent: Thursday, September 27, 2001 6:27 AM
> >> To: CAD_CAM_EDM_DRO@y...
> >> Subject: [CAD_CAM_EDM_DRO] Re: Stepper size?
> >>
> >>
> >> I have a program that calculates servo/stepper size based on load,
> >> ramp speed, screw pitch/type, slide type, etc. And outputs are data
> >> and graphs showing torque needed. Data entry is easy with great help
> >> files. Very usefull !
> >>
> >>
> >>
> >> --- In CAD_CAM_EDM_DRO@y..., zbadone@b... wrote:
> >> > I am in the process of designing my XYZ table. I am interested in
> >> > routing machinable wax for use with my casting furnace, light wood
> >> > routing and perhaps (light) engraving aluminum. Not very deep cuts
> >> in
> >> > the aluminum.
> >> >
> >> > I am trying to figure out a decent size stepper motor to use. I
> >came
> >> > accross a few on the net in the 125 oz/in model, one is a Size 23
> >> > ($40)Vexta PK226-02A, 200 s/r 3.6v@2A
> >> > and the other is a Size 34 ($25 used)125oz 2.5v@2... 200 s/r(steps
> >> per
> >> > rev).
> >> >
> >> > My table is what will be moving, made out of 3/4" cabinet grade
> >ply,
> >> > 24" * 30". What would be the recommended size based on my
> >> application?
> >> >
> >> > The over head gantry will house a Dewalt 1/4" laminat trimmer, not
> >> > much weight.
> >> >
> >> > Anybody have an opinion on these types of stepper or do you have
> >> > another source I could look at?
> >> >
> >> > Thanks.
> >>
> >>
> >> Addresses:
> >> FAQ: http://www.ktmarketing.com/faq.html
> >> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >>
> >> Post messages: CAD_CAM_EDM_DRO@y...
> >> Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> >> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> >> List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> >> Moderator: jmelson@a... timg@k... [Moderator]
> >> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >> bill,
> >> List Manager
> >>
> >>
> >>
> >> Your use of Yahoo! Groups is subject to
> >http://docs.yahoo.com/info/terms/
> >
> >
> >Addresses:
> >FAQ: http://www.ktmarketing.com/faq.html
> >FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >
> >Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> >Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> >List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> >Moderator: jmelson@... timg@... [Moderator]
> >URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >bill,
> >List Manager
> >
> >
> >
> >Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
> >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>