Re: [CAD_CAM_EDM_DRO] New guy with questions
Posted by
Smoke
on 2001-10-08 16:22:22 UTC
If your going to tap manually, best is to use both a center guide and a tap
wrench.
Clamp the part in the drill or mill so it won't move. Tap drill the hole.
Replace the drill with the center guide and then tap the hole.
If you are going to tap the hole using the machine to do the work, be sure
to use a machine tap and not a hand tap. In this case the tap is placed
directly in a collet for tapping. The machine is set to run slow as
possible. The feed is manually run down until the tap grabs. it will pull
itself in. As soon as the proper tap depth is reached the spindle direction
is reversed to pull the tap back out. The spindle brake IS NOT USED.
Tap depth can be "set" by wrapping a piece of tape around the tap at the
point of maximum depth desired.
Smoke
wrench.
Clamp the part in the drill or mill so it won't move. Tap drill the hole.
Replace the drill with the center guide and then tap the hole.
If you are going to tap the hole using the machine to do the work, be sure
to use a machine tap and not a hand tap. In this case the tap is placed
directly in a collet for tapping. The machine is set to run slow as
possible. The feed is manually run down until the tap grabs. it will pull
itself in. As soon as the proper tap depth is reached the spindle direction
is reversed to pull the tap back out. The spindle brake IS NOT USED.
Tap depth can be "set" by wrapping a piece of tape around the tap at the
point of maximum depth desired.
Smoke
> Hi I'm new to this group and I have a few questions that may seem so
> basic it will probably be ignored. But here goes . . .
>
> How do I tap a hole (in plain cold rolled steel) with a tap? Could I
> do this with a wrench?
>
Discussion Thread
gm4ta@i...
2001-10-07 20:53:21 UTC
New guy with questions
Tim Goldstein
2001-10-07 21:08:38 UTC
RE: [CAD_CAM_EDM_DRO] New guy with questions
Jon Elson
2001-10-07 21:38:17 UTC
Re: [CAD_CAM_EDM_DRO] New guy with questions
Alan Marconett KM6VV
2001-10-08 11:18:27 UTC
Re: [CAD_CAM_EDM_DRO] New guy with questions
Rich D.
2001-10-08 11:57:50 UTC
Re: [CAD_CAM_EDM_DRO] New guy with questions
Alan Marconett KM6VV
2001-10-08 15:47:08 UTC
New guy with questions
Smoke
2001-10-08 16:22:22 UTC
Re: [CAD_CAM_EDM_DRO] New guy with questions
gm4ta@i...
2001-10-10 08:30:18 UTC
Re: New guy with questions
ccs@m...
2001-10-10 08:53:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
Tim
2001-10-10 08:56:32 UTC
RE: [CAD_CAM_EDM_DRO] Re: New guy with questions
johnhe
2001-10-10 09:14:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
Tim
2001-10-10 09:38:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: New guy with questions
Alan Marconett KM6VV
2001-10-10 12:40:36 UTC
Re: New guy with questions
M. SHABBIR MOGHUL
2001-10-10 22:01:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
brian
2001-10-11 16:33:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
Smoke
2001-10-11 19:25:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
johnhe
2001-10-12 08:27:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
Smoke
2001-10-12 08:36:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
johnhe
2001-10-12 08:43:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
Smoke
2001-10-12 08:49:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
JanRwl@A...
2001-10-12 09:36:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
currinh@O...
2001-10-12 09:41:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
Smoke
2001-10-12 09:50:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
ccs@m...
2001-10-12 10:58:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
Fred Smith
2001-10-12 12:14:11 UTC
Re: New guy with questions
Eric Keller
2001-10-12 17:14:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
dkowalcz@d...
2001-10-12 20:45:43 UTC
Re: New guy with questions
Smoke
2001-10-12 20:58:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions
Ward M.
2001-10-12 23:23:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: New guy with questions
Ward M.
2001-10-12 23:35:58 UTC
RE: [CAD_CAM_EDM_DRO] Re: New guy with questions
Smoke
2001-10-13 08:07:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: New guy with questions