Re: [CAD_CAM_EDM_DRO] PCMIA Card and Socket Services Software
Posted by
David Goodfellow
on 2001-11-06 13:01:28 UTC
11 - O2Micro OZ6832/6833 CardBus Controller
The laptop has a parallel port, but that's used for the x, y and z axes. I
need the second port for the rotary table.
Thanks for the url. I'll check it out.
Dave Goodfellow
Northridge, CA
"No problem too small to baffle this expert"
The laptop has a parallel port, but that's used for the x, y and z axes. I
need the second port for the rotary table.
Thanks for the url. I'll check it out.
Dave Goodfellow
Northridge, CA
"No problem too small to baffle this expert"
----- Original Message -----
From: Alan Marconett KM6VV <KM6VV@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, November 06, 2001 12:52 PM
Subject: Re: [CAD_CAM_EDM_DRO] PCMIA Card and Socket Services Software
> Hi Dave,
>
> That's a tough one! What PCMCIA controller do you have in your laptop?
> 80365 or clone, or TI's? I've done AMD Élan 300's PCMCIA socket
> services; but unless you know what in in the laptop, it's hard to get
> the one that works. No files with the card? No parallel port on the
> laptop, I take it?
>
> You might find a driver at:
>
> http://www.pcmcia.org/
>
> HTH
>
> Alan KM6VV
>
>
> David Goodfellow wrote:
> >
> > Hi all:
> >
> > I'm trying to activate a parallel port PC card on my laptop in DOS, to
run a
> > rotary table. The card works fine in "DOS from Windows" but not without
> > Windows. Since my G-code software freaks out when Windows is involved,
I'm
> > caught between a rock and a hard spot.
> >
> > Does anyone know of a downloadable "Card and Socket Services" software
for
> > DOS? The only one I know of is discontinued but "available for $60, all
> > sales final, no tech support, no guarantee that it will work."
> >
> > Thanks in advance for any ideas.
> >
> > Dave Goodfellow
> > Northridge, CA
> > "No problem too small to baffle this expert"
> >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
David Goodfellow
2001-11-06 11:59:08 UTC
PCMIA Card and Socket Services Software
Alan Marconett KM6VV
2001-11-06 12:49:47 UTC
Re: [CAD_CAM_EDM_DRO] PCMIA Card and Socket Services Software
David Goodfellow
2001-11-06 13:01:28 UTC
Re: [CAD_CAM_EDM_DRO] PCMIA Card and Socket Services Software
Alan Marconett KM6VV
2001-11-06 13:30:25 UTC
Re: [CAD_CAM_EDM_DRO] PCMIA Card and Socket Services Software
David Goodfellow
2001-11-06 13:57:59 UTC
Re: [CAD_CAM_EDM_DRO] PCMIA Card and Socket Services Software
Alan Marconett KM6VV
2001-11-06 15:35:00 UTC
Re: [CAD_CAM_EDM_DRO] PCMIA Card and Socket Services Software
ballendo@y...
2001-11-06 17:06:00 UTC
Taig Software was Re: PCMIA Card and SS Software
David Goodfellow
2001-11-06 21:29:32 UTC
Re: [CAD_CAM_EDM_DRO] Taig Software was Re: PCMIA Card and SS Software