CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc]

Posted by Jon Elson
on 2001-11-22 13:33:24 UTC
shymu@... wrote:

> --- In CAD_CAM_EDM_DRO@y..., carlcnc@y... wrote:
>
> > I have often wondered WHY ther are no US manf of this type
> > motor/spindle??
>
> > Carl
>
> What is the reason for using hi-freq motors/spindles ?

High spindle speeds with direct drive, and no motor brushes.
At 60 Hz, you are limited to 3600 RPM. At 600 Hz, a 2-pole
induction motor will run close to 36,000 RPM. If you need
to go faster, just up the frequency (and voltage).

Jon

Discussion Thread

carlcnc@y... 2001-11-22 06:41:15 UTC hi-freq motors[perske etc] shymu@b... 2001-11-22 07:15:12 UTC Re: hi-freq motors[perske etc] Peter Seddon 2001-11-22 08:36:24 UTC Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc] machines@n... 2001-11-22 12:17:07 UTC Re: hi-freq motors[perske etc] JanRwl@A... 2001-11-22 13:13:33 UTC Re: [CAD_CAM_EDM_DRO] hi-freq motors[perske etc] Jon Elson 2001-11-22 13:31:28 UTC Re: [CAD_CAM_EDM_DRO] hi-freq motors[perske etc] Jon Elson 2001-11-22 13:33:24 UTC Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc] carlcnc@y... 2001-11-22 13:37:15 UTC Re: hi-freq motors[perske etc] carlcnc@y... 2001-11-22 13:41:36 UTC Re: hi-freq motors[perske etc]CAUTION! JanRwl@A... 2001-11-22 13:47:43 UTC Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc] Jon Elson 2001-11-22 14:03:18 UTC Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc] Brian 2001-11-22 17:26:53 UTC Re: [CAD_CAM_EDM_DRO] hi-freq motors[perske etc] machines@n... 2001-11-22 17:57:56 UTC Re: hi-freq motors[perske etc] Brian 2001-11-22 18:00:04 UTC Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc] JanRwl@A... 2001-11-22 21:04:18 UTC Re: [CAD_CAM_EDM_DRO] hi-freq motors[perske etc] Jon Elson 2001-11-22 21:32:19 UTC Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc]CAUTION! Jon Elson 2001-11-22 21:54:46 UTC Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc] Jon Elson 2001-11-22 22:00:20 UTC Re: [CAD_CAM_EDM_DRO] hi-freq motors[perske etc] machines@n... 2001-11-23 01:16:40 UTC Re: hi-freq motors[perske etc] mika.salmi@p... 2001-11-23 04:29:52 UTC Re: hi-freq motors[perske etc] Brian 2001-11-23 06:26:34 UTC Re: [CAD_CAM_EDM_DRO] hi-freq motors[perske etc] JanRwl@A... 2001-11-23 13:45:09 UTC Re: [CAD_CAM_EDM_DRO] hi-freq motors[perske etc] Jon Elson 2001-11-23 14:31:55 UTC Re: [CAD_CAM_EDM_DRO] hi-freq motors[perske etc] Jon Elson 2001-11-23 21:29:15 UTC Re: [CAD_CAM_EDM_DRO] Re: hi-freq motors[perske etc]