Re: [CAD_CAM_EDM_DRO] Calculations for XL 037 pullies and cutters
Posted by
Alan Marconett KM6VV
on 2001-11-26 14:44:17 UTC
Hi John S.,
Yes, I think I see this now. Turn blank dia to OD, cutter tip starts
out on OD, and cuts in by the infeed distance. The cutter has a
specified tip width and the flanks of the tool are at a specified
angle. "FLY" across the edge of the timing belt pulley, then repeat
for each of the tooth locations. That's it?
Thanks for the help!
Alan KM6VV
machines@... wrote:
Yes, I think I see this now. Turn blank dia to OD, cutter tip starts
out on OD, and cuts in by the infeed distance. The cutter has a
specified tip width and the flanks of the tool are at a specified
angle. "FLY" across the edge of the timing belt pulley, then repeat
for each of the tooth locations. That's it?
Thanks for the help!
Alan KM6VV
machines@... wrote:
>
> The XL range of pullies all have a pitch of 0.200"
> The included angle of the cutter is 50 degrees and the width of the
> cutter at the tip is 0.052"
> This can be ground up like a fly cutter and that's all the cutter
> information you need.
>
> The pitch circle diameter of the pulley is found by multipling the
> number of teeth by the pitch and dividing the total by Pi.
> Example shown for 30 Tooth pulley:-
> [30 * 0.200] = 6 / 3.1412 = 1.910" dia
>
> Outside diameter is found by subtracting a constant K from the PCD.
> Same example again:-
> 1.910 - 0.020 = 1.890" dia
> The constant K is 0.020 for the whole of the XL range.
>
> Last piece of information needed is the depth of the cutter infeed.
> Again this is constant throughout the XL range at 0.065" deep.
>
> If anybody want's any more details for other tooth forms like MP, l
> or H series than have a look in the files section for a file called
> pulley.jpg or go to this link:-
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/Pulley.jpg
> All the other detail are shown there. The constant K id in column J
>
> John S.
Discussion Thread
machines@n...
2001-11-26 13:06:25 UTC
Calculations for XL 037 pullies and cutters
Alan Marconett KM6VV
2001-11-26 14:44:17 UTC
Re: [CAD_CAM_EDM_DRO] Calculations for XL 037 pullies and cutters
machines@n...
2001-11-26 15:04:16 UTC
Re: Calculations for XL 037 pullies and cutters
phrh@w...
2001-11-26 15:18:12 UTC
Re: Calculations for XL 037 pullies and cutters
Chris Clough
2001-11-26 15:29:27 UTC
Plasma control
Darrell Daniels
2001-11-26 17:30:26 UTC
Re: [CAD_CAM_EDM_DRO] Plasma control
Alan Marconett KM6VV
2001-11-26 18:50:37 UTC
Re: [CAD_CAM_EDM_DRO] Calculations for XL 037 pullies and cutters
Steve Smith
2001-11-26 20:50:16 UTC
Re: [CAD_CAM_EDM_DRO] Plasma control
Chris Clough
2001-11-26 21:30:15 UTC
Plasma Cutting Software?
cncdxf@a...
2001-11-27 08:15:42 UTC
Re: Plasma Cutting Software?
Chris Clough
2001-11-27 08:19:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: Plasma Cutting Software?
roundrocktom@y...
2001-11-27 09:15:24 UTC
Re: Plasma control
Carol & Jerry Jankura
2001-11-27 14:04:00 UTC
RE: [CAD_CAM_EDM_DRO] Plasma Cutting Software?