CAD CAM EDM DRO - Yahoo Group Archive

Re: gecko wiring help

on 2001-12-13 13:33:20 UTC
Hi Matt,

That's a 15 pin connector for the game port power. I have three new
G201's on the way from Gecko, and as I'll be building them up for
someone else, I'll make up a schematic for the PS/driver box, and a
procedure for testing. This will probably be during the next two
weeks. I'll copy you on the doc's if you're interested.

If you're in the area, I could probably look over, / check out, your
power supply motors and driver setup.

TurboCNC should make a simple checkout. I should be able to send you
the configuration file I will use (if you use the same pinout).

What pinout are you using for the DB25? I've copied one of the MaxNC
step/directon pinouts, as I have that I can run.

I'm on the central coast of California, just outside of Santa Cruz, if
this helps.

We'll get you going!

Alan KM6VV


pkranger63 wrote:
>
> Gave that a try and still a no go. For my +5v I just bought a 9 pin
> connector at radio shack and am just running one wire from it to the
> gecko box, is this correct? Any other areas I should check or double
> check in the hardware or software. I am trying to use either a demo
> of Master5 or Turbocnc.
>
> Thanks again,
> Matt

Discussion Thread

pkranger63 2001-12-11 18:11:18 UTC gecko wiring help Alan Marconett KM6VV 2001-12-11 20:12:13 UTC Re: [CAD_CAM_EDM_DRO] gecko wiring help pkranger63 2001-12-11 21:00:02 UTC Re: gecko wiring help Carol & Jerry Jankura 2001-12-11 21:25:09 UTC RE: [CAD_CAM_EDM_DRO] Re: gecko wiring help Dennis Cranston 2001-12-12 07:17:17 UTC RE: [CAD_CAM_EDM_DRO] Re: gecko wiring help Alan Marconett KM6VV 2001-12-12 10:31:45 UTC Re: gecko wiring help Alan Marconett KM6VV 2001-12-12 11:10:32 UTC Re: gecko wiring help pkranger63 2001-12-12 21:04:46 UTC Re: gecko wiring help tgoldsteinsprint1 2001-12-13 06:30:21 UTC Re: gecko wiring help pkranger63 2001-12-13 06:59:19 UTC Re: gecko wiring help tgoldsteinsprint1 2001-12-13 07:50:25 UTC Re: gecko wiring help Alan Marconett KM6VV 2001-12-13 13:00:42 UTC Re: gecko wiring help Alan Marconett KM6VV 2001-12-13 13:33:20 UTC Re: gecko wiring help pkranger63 2001-12-13 20:08:18 UTC Re: gecko wiring help Alan Marconett KM6VV 2001-12-13 20:20:04 UTC Re: gecko wiring help Alex Canale 2001-12-14 05:26:18 UTC RE: [CAD_CAM_EDM_DRO] I am not selling CNC knee mills! tgoldsteinsprint1 2001-12-14 06:34:41 UTC Re: gecko wiring help Dan Mauch 2001-12-14 07:41:31 UTC Gecko 201/G320 common signal GROUND! wanliker@a... 2002-01-06 14:22:43 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201/G320 common signal GROUND! Dan Mauch 2002-01-07 09:41:36 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201/G320 common signal GROUND!