CAD CAM EDM DRO - Yahoo Group Archive

Re: gecko wiring help

on 2001-12-13 20:20:04 UTC
Hi Matt,

Glad to hear you've got it going! Where were you getting +5 from
before?

Yeah, you should check out Vector CAD/CAM. The demo is good. Go
through all the exercises, and I think you'll do just fine!

Again, Congratulations!

Alan KM6VV
(whew!)

pkranger63 wrote:
>
> Woohoo got the thing working. I tried Tims idea of running my 5v off
> one of my drive power supply cables (not the 12v) and vrrooomm the
> motor was working. Very big relief. Just gotta mount them on the
> mill and and pick out a cad/cam program, I've been leaning towards
> vector based on the great comments about the program and the demo
> seems too "agree" with me. Thanks for all the help. More questions
> to follow I am sure though!
>
> Matt
>
> -- In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> > Hi Tim,
> >
> > Reversing one coil? How can that help? The current through the
> coil
> > gets reversed anyway by the H-bridge. It would just change the
> > direction of rotation, because the sequence of excitation to the
> > windings would essentially be different.
> >
> > Alan KM6VV

Discussion Thread

pkranger63 2001-12-11 18:11:18 UTC gecko wiring help Alan Marconett KM6VV 2001-12-11 20:12:13 UTC Re: [CAD_CAM_EDM_DRO] gecko wiring help pkranger63 2001-12-11 21:00:02 UTC Re: gecko wiring help Carol & Jerry Jankura 2001-12-11 21:25:09 UTC RE: [CAD_CAM_EDM_DRO] Re: gecko wiring help Dennis Cranston 2001-12-12 07:17:17 UTC RE: [CAD_CAM_EDM_DRO] Re: gecko wiring help Alan Marconett KM6VV 2001-12-12 10:31:45 UTC Re: gecko wiring help Alan Marconett KM6VV 2001-12-12 11:10:32 UTC Re: gecko wiring help pkranger63 2001-12-12 21:04:46 UTC Re: gecko wiring help tgoldsteinsprint1 2001-12-13 06:30:21 UTC Re: gecko wiring help pkranger63 2001-12-13 06:59:19 UTC Re: gecko wiring help tgoldsteinsprint1 2001-12-13 07:50:25 UTC Re: gecko wiring help Alan Marconett KM6VV 2001-12-13 13:00:42 UTC Re: gecko wiring help Alan Marconett KM6VV 2001-12-13 13:33:20 UTC Re: gecko wiring help pkranger63 2001-12-13 20:08:18 UTC Re: gecko wiring help Alan Marconett KM6VV 2001-12-13 20:20:04 UTC Re: gecko wiring help Alex Canale 2001-12-14 05:26:18 UTC RE: [CAD_CAM_EDM_DRO] I am not selling CNC knee mills! tgoldsteinsprint1 2001-12-14 06:34:41 UTC Re: gecko wiring help Dan Mauch 2001-12-14 07:41:31 UTC Gecko 201/G320 common signal GROUND! wanliker@a... 2002-01-06 14:22:43 UTC Re: [CAD_CAM_EDM_DRO] Gecko 201/G320 common signal GROUND! Dan Mauch 2002-01-07 09:41:36 UTC RE: [CAD_CAM_EDM_DRO] Gecko 201/G320 common signal GROUND!