Re: [CAD_CAM_EDM_DRO] serial cable current capabilities
Posted by
Doug Harrison
on 2002-01-09 15:38:55 UTC
I recently used a trailer light connector for an industrial application.
They work great and are cheap at Walmart.
Doug
They work great and are cheap at Walmart.
Doug
----- Original Message -----
From: Alan Marconett KM6VV <KM6VV@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, January 09, 2002 6:03 PM
Subject: Re: [CAD_CAM_EDM_DRO] serial cable current capabilities
> Hi Scot,
>
> "EACH" of the motors has it's own cable and connector, so no problem!
> Another good connector that's been suggested is a "microphone" connector
> (Radio Shack), as used on communications gear. And I've just
> successfully used DIN connectors on a new PS/driver (and I believe this
> is common practice in industry).
>
> Alan KM6VV
>
>
> Scot Rogers wrote:
> >
> > ~
> > ~Hi Scot,
> > ~
> > ~I'm using DB15's (I had a lot of 'em), and they work fine. Trouble is
> > ~getting 18 ga. wire into the pins! You can also use a PAIR of wires
and
> > ~pins per lead. I have quite a few motors wired with DB15's. Even
> > ~Unipolar motors, where I use an additional pair of pins for the
"common"
> > ~(2nd common for 6 wire motors). The common pins are ignored for a
> > ~bipolar motor. I was even thinking of adding the current selection
> > ~resistor to the connector as well. BUT, I'd caution that you provide a
> > ~"minimum current" resistor at the Gecko. Otherwise, well you know what
> > ~will happen!
> > ~
> > ~Alan KM6VV
> >
> > Thanks Alan,
> >
> > One question though. *Each* of the motors draw 3.3 amps. Does that
change
> > anything?
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
Multi-Volti Devices
2002-01-09 13:18:29 UTC
specialty tool reference
Scot Rogers
2002-01-09 14:11:14 UTC
serial cable current capabilities
Alan Marconett KM6VV
2002-01-09 14:23:21 UTC
Re: [CAD_CAM_EDM_DRO] serial cable current capabilities
Scot Rogers
2002-01-09 14:49:39 UTC
RE: [CAD_CAM_EDM_DRO] serial cable current capabilities
Alan Marconett KM6VV
2002-01-09 15:00:49 UTC
Re: [CAD_CAM_EDM_DRO] serial cable current capabilities
Doug Harrison
2002-01-09 15:36:54 UTC
Re: [CAD_CAM_EDM_DRO] specialty tool reference
Randy Gordon-Gilmore
2002-01-09 15:38:19 UTC
Re: serial cable current capabilities
Doug Harrison
2002-01-09 15:38:55 UTC
Re: [CAD_CAM_EDM_DRO] serial cable current capabilities
Alan Marconett KM6VV
2002-01-09 17:12:09 UTC
Re: serial cable current capabilities
Alan Marconett KM6VV
2002-01-09 17:14:33 UTC
Re: [CAD_CAM_EDM_DRO] serial cable current capabilities
mariss92705
2002-01-09 18:12:58 UTC
Re: serial cable current capabilities
Randy Gordon-Gilmore
2002-01-09 18:19:11 UTC
Re: serial cable current capabilities
ballendo
2002-01-09 21:12:48 UTC
Re: serial cable current capabilities
JanRwl@A...
2002-01-09 21:48:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: serial cable current capabilities
Alan Marconett KM6VV
2002-01-09 22:58:05 UTC
Re: serial cable current capabilities
Scot Rogers
2002-01-10 01:02:16 UTC
RE: [CAD_CAM_EDM_DRO] Re: serial cable current capabilities
Ian Wright
2002-01-10 03:38:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: serial cable current capabilities
Carol & Jerry Jankura
2002-01-10 06:40:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: serial cable current capabilities
JanRwl@A...
2002-01-10 20:36:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: serial cable current capabilities
waynegramlich
2002-01-10 21:01:06 UTC
Re: serial cable current capabilities
ledinger
2002-01-10 21:10:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: serial cable current capabilities
waynegramlich
2002-01-10 21:24:05 UTC
Re: serial cable current capabilities
Tim Goldstein
2002-01-10 21:27:05 UTC
RE: [CAD_CAM_EDM_DRO] Re: serial cable current capabilities