CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] DRO

Posted by ccs@m...
on 2002-02-01 08:48:20 UTC
> The one I have is the stretched strip type and the encoder head has just
> four connections - I am assuming power, ground, channel A and channel B. As
> one of the tracks on the flexy connector is wider than the rest I would
> assume that this is probably ground but that then leaves the other three.
> The application I have in mind doesn't need much accuracy so this strip
> should be OK if I can just work out the connections, voltage etc.

If the printer isn't too dead you could plug it in and measure the
voltages on the pins. My little linear module (unlike the rotary one)
has a cap on the carrier pcb, so that should identify the power leads,
then it is only a question of which is which. It doesn't matter if
you swap the quadrature leads - all it will do is make the encoder
count in the opposite direction, so swap them until you have the
orientation you want.

Chris

-------------------------------------------------
Christopher C. Stratton
Engineer, Instrument Maker, and Horn Player
ccs@... 617 628 1062
http://web.mit.edu/~stratton/www/brassbuild.html

Discussion Thread

paul@x... 1999-05-17 07:09:09 UTC Re: DRO Jon Elson 1999-05-17 22:30:45 UTC Re: DRO PTENGIN@x... 1999-07-21 16:14:26 UTC Re: DRO Laverne Karras 1999-07-22 06:49:59 UTC Re: DRO Russ Kepler 1999-07-22 07:14:55 UTC Re: DRO Randolph Lee 1999-07-22 08:25:20 UTC Re: DRO Rudy du Preez 2000-02-09 00:52:27 UTC DRO smcdonal 2000-02-09 03:56:02 UTC Re: DRO A. G. Eckstein 2000-02-09 14:34:52 UTC Re: DRO SMITH, THOMAS B. (JSC-DX) 2000-02-10 10:08:36 UTC RE: DRO PTENGIN@a... 2000-02-10 10:34:29 UTC Re: RE: DRO Rudy du Preez 2000-02-10 22:02:01 UTC RE: DRO Jean-Luc Luczak 2000-02-11 00:05:19 UTC Re: RE: DRO Dan Mauch 2000-02-11 06:25:05 UTC Re: RE: DRO Dan Mauch 2000-02-11 07:02:34 UTC Re: RE: DRO SMITH, THOMAS B. (JSC-DX) 2000-02-11 09:54:34 UTC RE:DRO PTENGIN@a... 2000-02-11 10:37:26 UTC Re: RE:DRO SMITH, THOMAS B. (JSC-DX) 2000-02-11 10:45:08 UTC RE: DRO Joe Landau 2000-02-23 21:08:49 UTC Re: DRO A. G. Eckstein 2000-02-24 14:08:20 UTC Re: DRO wanliker@a... 2000-02-24 16:22:55 UTC Re: DRO A. G. Eckstein 2000-02-24 17:06:02 UTC Re: DRO Ted Robbins 2000-02-24 17:52:50 UTC Re: DRO Joe Landau 2000-02-24 21:31:07 UTC Re: DRO ptengin@a... 2000-02-24 22:22:58 UTC Re: DRO Terry May 2000-02-24 13:48:07 UTC RE: DRO Marshall Pharoah 2000-02-25 05:38:13 UTC Re: DRO Steve Carlisle 2000-02-25 08:23:15 UTC Re: DRO wanliker@a... 2000-02-25 09:00:12 UTC Re: DRO Ian Wright 2000-02-25 13:13:09 UTC Re: DRO A. G. Eckstein 2000-02-25 15:51:51 UTC Re: DRO A. G. Eckstein 2000-02-25 15:54:00 UTC Re: DRO A. G. Eckstein 2000-02-25 16:32:47 UTC Re: DRO A. G. Eckstein 2000-02-25 16:36:20 UTC Re: DRO Jon Elson 2000-02-26 00:19:48 UTC Re: DRO A. G. Eckstein 2000-02-26 04:29:28 UTC Re: DRO beer@s... 2000-03-10 11:21:23 UTC DRO D.F.S. 2000-03-10 13:47:29 UTC Re: [CAD_CAM_EDM_DRO] DRO Murray Leshner 2000-04-06 22:58:50 UTC DRO Ron Ginger 2000-04-07 05:36:19 UTC Re:DRO wanliker@a... 2000-12-30 16:18:14 UTC Re: [CAD_CAM_EDM_DRO] DRO Tim Goldstein 2000-12-30 22:45:36 UTC RE: [CAD_CAM_EDM_DRO] DRO wanliker@a... 2000-12-31 08:12:58 UTC Re: [CAD_CAM_EDM_DRO] DRO rekmac 2002-01-18 07:53:26 UTC DRO babinda01 2002-01-30 13:25:17 UTC DRO ccs@m... 2002-01-30 13:46:10 UTC Re: [CAD_CAM_EDM_DRO] DRO ballendo 2002-01-30 20:44:14 UTC Re: DRO Jon Elson 2002-01-30 22:35:11 UTC Re: [CAD_CAM_EDM_DRO] DRO Robert Bachman 2002-01-31 06:42:19 UTC Re: [CAD_CAM_EDM_DRO] Re: DRO Ian W. Wright 2002-02-01 03:28:26 UTC DRO ccs@m... 2002-02-01 07:11:05 UTC Re: [CAD_CAM_EDM_DRO] DRO Ian W. Wright 2002-02-01 08:36:42 UTC Re: [CAD_CAM_EDM_DRO] DRO ccs@m... 2002-02-01 08:48:20 UTC Re: [CAD_CAM_EDM_DRO] DRO Lew 2002-02-01 10:01:47 UTC RE: [CAD_CAM_EDM_DRO] DRO Ian W. Wright 2002-02-01 10:22:59 UTC Re: [CAD_CAM_EDM_DRO] DRO Ian W. Wright 2002-02-01 10:25:14 UTC Re: [CAD_CAM_EDM_DRO] DRO Lew 2002-02-01 15:19:17 UTC RE: [CAD_CAM_EDM_DRO] DRO Ian W. Wright 2002-02-01 16:27:43 UTC Re: [CAD_CAM_EDM_DRO] DRO Lew 2002-02-01 18:12:14 UTC RE: [CAD_CAM_EDM_DRO] DRO Arthur Shute 2002-02-18 10:52:28 UTC DRO Ken Jenkins 2002-04-02 06:13:16 UTC Re: DRO James Owens 2002-05-21 08:17:26 UTC DRO Gene 2003-02-06 04:19:19 UTC DRO Hans Wedemeyer 2003-02-06 09:14:20 UTC Re: [CAD_CAM_EDM_DRO] DRO Gene 2003-02-06 10:13:41 UTC Re: [CAD_CAM_EDM_DRO] DRO Hans Wedemeyer 2003-02-06 11:42:54 UTC Re: [CAD_CAM_EDM_DRO] DRO mayfieldtm <mayfiet@i... 2003-02-06 11:56:46 UTC Re: DRO Myron Cherry 2003-02-06 22:33:45 UTC Re: [CAD_CAM_EDM_DRO] DRO krmnalmind0351 <krmnalmind@a... 2003-02-07 09:21:32 UTC Re: DRO Hans Wedemeyer 2003-02-07 11:38:49 UTC Re: [CAD_CAM_EDM_DRO] Re: DRO Raymond Heckert 2003-02-07 17:50:25 UTC Re: [CAD_CAM_EDM_DRO] DRO dro_guy <dro_guy@h... 2003-02-07 22:17:05 UTC Re: DRO Doug Fortune 2003-02-08 17:47:17 UTC Re: [CAD_CAM_EDM_DRO] Re: DRO k8zre <rfs@c... 2003-02-08 18:38:54 UTC Re: DRO Doug Fortune 2003-02-08 20:12:15 UTC Re: [CAD_CAM_EDM_DRO] Re: DRO Myron Cherry 2003-02-08 20:24:34 UTC Re: [CAD_CAM_EDM_DRO] Re: DRO k8zre <rfs@c... 2003-02-09 06:46:29 UTC Re: DRO Doug Fortune 2003-02-09 12:05:01 UTC Re: [CAD_CAM_EDM_DRO] Re: DRO k8zre <rfs@c... 2003-02-09 16:23:18 UTC Re: DRO dro_guy <dro_guy@h... 2003-02-10 01:02:10 UTC Re: DRO dro_guy <dro_guy@h... 2003-02-10 01:05:04 UTC Re: DRO James Owens 2003-07-12 10:30:01 UTC DRO k8zre 2003-08-02 14:37:41 UTC DRO ROBERT ALLAN 2004-01-20 09:08:32 UTC DRO wanliker@a... 2006-04-25 10:39:16 UTC DRO k8zre 2008-04-06 17:48:54 UTC DRO bear_machine 2010-04-19 19:46:02 UTC DRO fbcsnh@c... 2010-04-20 08:15:38 UTC Re: [CAD_CAM_EDM_DRO] DRO smirob1 2010-04-20 15:11:27 UTC Re: DRO bear_machine 2010-04-20 23:45:22 UTC Re: DRO smirob1 2010-04-21 15:06:02 UTC Re: DRO roboticscnc 2010-04-22 07:35:05 UTC Re: DRO Drew Reynolds 2011-04-25 16:42:14 UTC DRO Art Eckstein 2011-04-25 16:54:14 UTC Re: [CAD_CAM_EDM_DRO] DRO Tom 2011-04-25 17:00:07 UTC Re: DRO wotisname 2011-04-25 17:04:15 UTC Re: DRO robin 2011-04-27 08:27:00 UTC Re: [CAD_CAM_EDM_DRO] DRO Joe Hovel 2011-04-27 08:29:57 UTC Re: DRO wildhorsesoftware 2011-04-27 08:54:34 UTC Re: DRO robin 2011-05-01 16:47:39 UTC Re: [CAD_CAM_EDM_DRO] DRO Rjreese29 2011-05-01 16:47:39 UTC Re: [CAD_CAM_EDM_DRO] DRO