Posts by PTENGIN@a...

PTENGIN@a... 1999-07-09 19:28:40 UTC Re: [CAD_CAM_EDM_DRO] The cutting edge? PTENGIN@a... 1999-07-09 21:38:53 UTC Re: [CAD_CAM_EDM_DRO] The cutting edge? PTENGIN@a... 1999-08-03 10:26:11 UTC Re: Opto Isolators & Parallel Ports PTENGIN@a... 1999-08-18 19:01:53 UTC Re: Power Supplies PTENGIN@a... 1999-08-18 22:24:52 UTC Re: Projects Status PTENGIN@a... 1999-08-26 15:54:34 UTC Re: driver performance PTENGIN@a... 1999-09-10 15:48:31 UTC Re: Low cost Servo Controller PTENGIN@a... 1999-09-10 19:28:24 UTC Re: Servo-PWM-DSP PTENGIN@a... 1999-09-13 16:36:02 UTC Re: Low cost Servo Controller PTENGIN@a... 1999-09-13 21:44:43 UTC Re: Low cost Servo Controller PTENGIN@a... 1999-09-13 21:47:50 UTC Re: Servo Products Mill PTENGIN@a... 1999-09-21 10:04:48 UTC Re: Low cost Servo Controller PTENGIN@a... 1999-09-24 02:30:25 UTC Re: Another Possible Lower cost Servo Controller? PTENGIN@a... 1999-09-24 14:22:05 UTC Re: Another Possible Lower cost Servo Controller? PTENGIN@a... 1999-09-24 14:31:05 UTC Re: Introduction/Ideas/Questions PTENGIN@a... 1999-10-09 10:32:03 UTC Re: Blue Sky PTENGIN@a... 1999-10-19 18:56:00 UTC Re: Re: What do we want? PTENGIN@a... 1999-10-22 02:21:41 UTC Re: Digest Number 221 PTENGIN@a... 1999-12-04 17:59:49 UTC Re: Re:Stepper program w/Encoders? PTENGIN@a... 1999-12-04 18:03:26 UTC Re: Re: Neat Mini mill with all the good stuff PTENGIN@a... 1999-12-23 04:23:40 UTC Re: Distractions.... PTENGIN@a... 1999-12-27 13:24:39 UTC Re: Who runs CNC CONTROL on a Rotary Converter? PTENGIN@a... 2000-01-05 01:08:58 UTC Re: RF-45 mill almost done PTENGIN@a... 2000-01-18 10:01:31 UTC Re: Mill/Drills PTENGIN@a... 2000-01-19 09:27:31 UTC Re: Steppers versus Servos PTENGIN@a... 2000-01-20 11:02:21 UTC Re: got catalog with motion stuff PTENGIN@a... 2000-01-20 22:12:54 UTC Re: Table mounted tool changer PTENGIN@a... 2000-01-21 10:31:09 UTC Re: tool changers PTENGIN@a... 2000-01-22 00:58:01 UTC Re: Van Norman #12 Milling Machine PTENGIN@a... 2000-01-24 01:47:03 UTC Re: Van Norman #12 Milling Machine PTENGIN@a... 2000-01-25 01:17:15 UTC Re: Van Norman #12 Milling Machine PTENGIN@a... 2000-01-25 19:18:01 UTC Re: Re: Van Norman #12 Milling Machine PTENGIN@a... 2000-01-26 01:58:53 UTC Re: Re: backlash reduction PTENGIN@a... 2000-01-28 13:55:12 UTC Re: [OT]Coloring Metals PTENGIN@a... 2000-01-28 14:52:11 UTC Re: Re: Grizzley PTENGIN@a... 2000-01-28 14:56:40 UTC Re: Use a scope to determine overvoltage needed for stepper... PTENGIN@a... 2000-01-29 02:14:32 UTC Re: [OT]Coloring Metals PTENGIN@a... 2000-01-29 02:17:53 UTC Re: [OT]Coloring Metals PTENGIN@a... 2000-01-31 11:58:11 UTC Re: single phase motor speed control PTENGIN@a... 2000-02-01 09:41:20 UTC Re: Serial port protocol PTENGIN@a... 2000-02-04 10:08:25 UTC Re: G02, G03 & EMC PTENGIN@a... 2000-02-04 10:27:45 UTC Re: home made injection mold PTENGIN@a... 2000-02-04 10:29:56 UTC Re: home made injection mold PTENGIN@a... 2000-02-05 19:12:22 UTC Re: Plastic Grinders. PTENGIN@a... 2000-02-07 10:15:42 UTC Re: RE: BDI install disk for EMC PTENGIN@a... 2000-02-08 01:10:31 UTC Re: Shinano Kenshi 24VDC Servo Motor with Encoder Res: 500... PTENGIN@a... 2000-02-10 10:34:29 UTC Re: RE: DRO PTENGIN@a... 2000-02-10 23:02:56 UTC Re: BDI install disk for EMC PTENGIN@a... 2000-02-11 10:37:26 UTC Re: RE:DRO PTENGIN@a... 2000-02-12 01:22:03 UTC Re: CAD Question PTENGIN@a... 2000-02-17 01:03:20 UTC Re: OpenCNC??? PTENGIN@a... 2000-02-17 18:29:43 UTC Re: NEW member Suitable conversions? PTENGIN@a... 2000-02-18 01:57:22 UTC Re: Ballscrew conversion PTENGIN@a... 2000-02-18 12:05:29 UTC Re: clean plasma