CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table

Posted by ljgeib@a...
on 2002-03-28 19:00:44 UTC
the best setup I've seen is a plasma cutter that had a water bath that came
to the bottom of the work. It didn't have any of the clouds of dirt generaly
associated with the process.

Larry

In a message dated 3/28/02 6:34:49 PM Pacific Standard Time,
davemucha@... writes:


>
> Another question as to how dirty this work is.
>
> Does the effluent (is there and term ? on my lathe I make swarth)
> get above the table ?
>
> I had though of using uni-strut as the main rail and to hang it
> upside down and use the uni-stru rollers (a style like glass shower
> doors) the roller being above the table and inside the track.
>
> It seems that using angle iron and some V rollers might be just as
> good or better.
>
> If the effluent does not rise, then I could hang the gantry and let
> it roll in that manner.
>
> about table size, I was not planning on a large unit, probably only 5
> foot by 10 foot to allow me to cut a 4 ft x 8 ft sheet of stock. The
> overhang would allow the cutting tip to move to the edge of the stock.
>
> about cutting speed, 500 inches a minute ? wow ! now that is FAST !
> I was timing my current table NEMA-23, 2:1 pulleys on a 1/2-13
> leadscrew fed from a 12 v supply running on a serial controller and
> only getting 4 inches a minute. (I am chewing my nails waiting for
> my Gecko's to arrive.)
>



[Non-text portions of this message have been removed]

Discussion Thread

dave_ace_me 2002-03-28 08:35:29 UTC plasma cutting table CL 2002-03-28 10:09:38 UTC Re: [CAD_CAM_EDM_DRO] plasma cutting table dave_ace_me 2002-03-28 18:32:08 UTC Re: plasma cutting table ljgeib@a... 2002-03-28 19:00:44 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table dave_ace_me 2002-03-28 20:03:57 UTC Re: plasma cutting table Raymond Heckert 2002-03-28 20:10:05 UTC Re: [CAD_CAM_EDM_DRO] plasma cutting table dave_ace_me 2002-03-28 20:53:24 UTC Re: plasma cutting table aspaguy 2002-03-28 21:21:28 UTC Re: plasma cutting table aspaguy 2002-03-28 21:42:46 UTC Re: plasma cutting table Darrell Daniels 2002-03-28 21:43:14 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table aspaguy 2002-03-28 21:51:24 UTC Re: plasma cutting table Paul Weber 2002-03-29 00:21:47 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table dave_ace_me 2002-03-29 04:58:26 UTC Re: plasma cutting table roundrocktom 2002-03-29 07:22:20 UTC Re: plasma cutting table Chris L 2002-03-29 16:07:08 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table Chris L 2002-03-29 16:23:18 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table Chris L 2002-03-29 16:39:35 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table ljgeib@a... 2002-03-29 18:55:07 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table dave_ace_me 2002-03-29 19:23:53 UTC Re: plasma cutting table Chris L 2002-03-29 20:17:14 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table RC 2002-03-30 11:48:39 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table Darrell Daniels 2002-03-30 12:01:23 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table aspaguy 2002-04-01 20:36:29 UTC Re: plasma cutting table Chris L 2002-04-02 19:52:34 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table batwings@i... 2002-04-03 04:44:25 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table Scott 2002-04-03 06:25:31 UTC Re: [CAD_CAM_EDM_DRO] Re: plasma cutting table aspaguy 2002-04-03 19:37:35 UTC Re: plasma cutting table