CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: cap question

Posted by JanRwl@A...
on 2002-04-01 23:01:24 UTC
In a message dated 02-Apr-02 00:53:45 Central Standard Time,
ccq@... writes:


> Couldn't you use a transistor to drop it? Consider: One of the ways zeners
> are
> used to regulate voltage, is to put a potentiometer between it and ground.
> Now
> if at that zener/pot juncture, you connect the base of an NPN transistor
> with
> the emitter going to ground, and the collector connected above the zener,
> the
> transistor would drop the voltage everytime the zener reached it's limit.
> An
> extra pot might be needed between the juncture and the transistor base, in
> order
> to adjust the transistor properly, but you could get away with using a
> lightweight zener that way.


This is like saying, "Couldn't you just get a fatter stick to drag out the
window, to slow the car down, better?" Really! No kidding! Besides, this
approach would be for regulating current, not voltage... It is too late
(01:03, here!). I can't think. But this is a WRONG approach. Tomorrow.


[Non-text portions of this message have been removed]

Discussion Thread

Mike Snodgrass 2002-04-01 14:34:59 UTC cap question Scott M. Thomas 2002-04-01 14:53:55 UTC RE: [CAD_CAM_EDM_DRO] cap question RC 2002-04-01 15:00:45 UTC Re: [CAD_CAM_EDM_DRO] cap question lenskeeper2000 2002-04-01 15:27:20 UTC Re: cap question Tim Goldstein 2002-04-01 15:41:46 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question Mike Snodgrass 2002-04-01 16:47:03 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question n4onl 2002-04-01 17:42:04 UTC Re: cap question Paul Weber 2002-04-01 19:50:46 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question JanRwl@A... 2002-04-01 20:41:36 UTC Re: [CAD_CAM_EDM_DRO] cap question JanRwl@A... 2002-04-01 21:35:15 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question Bill Vance 2002-04-01 22:51:47 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question Jon Elson 2002-04-01 22:56:06 UTC Re: [CAD_CAM_EDM_DRO] cap question JanRwl@A... 2002-04-01 23:01:24 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question Jon Elson 2002-04-01 23:01:33 UTC Re: [CAD_CAM_EDM_DRO] cap question Jon Elson 2002-04-01 23:17:16 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question cadcamcenter 2002-04-02 00:12:07 UTC Re: cap question cadcamcenter 2002-04-02 00:19:02 UTC Re: cap question Mike Snodgrass 2002-04-02 07:00:48 UTC Re: [CAD_CAM_EDM_DRO] cap question Jon Elson 2002-04-02 10:53:10 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question Jon Elson 2002-04-02 11:05:18 UTC Re: [CAD_CAM_EDM_DRO] cap question Sven Peter 2002-04-02 16:31:15 UTC Re: [CAD_CAM_EDM_DRO] Re: cap question ballendo 2002-04-13 03:55:20 UTC Re: cap question