Re: [CAD_CAM_EDM_DRO] Gcode
Posted by
James Stevens
on 2002-06-05 14:03:16 UTC
Gene,
I'm just doing the same research. I believe the correct format is:
G41 DXX
where XX is the corresponding tool diameter in the tool list. The D
usually/should correspond to the same tool, T, as defined by TXX as follows:
T01
which selects tool 1 - this needs to be defined in your tool list.
HTH - I'm still learning and trying to apply cutter compensation to the
Gcode output by RasterFratz.
James
I'm just doing the same research. I believe the correct format is:
G41 DXX
where XX is the corresponding tool diameter in the tool list. The D
usually/should correspond to the same tool, T, as defined by TXX as follows:
T01
which selects tool 1 - this needs to be defined in your tool list.
HTH - I'm still learning and trying to apply cutter compensation to the
Gcode output by RasterFratz.
James
----- Original Message -----
From: "Gene" <capper@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, June 05, 2002 3:47 PM
Subject: [CAD_CAM_EDM_DRO] Gcode
> When you use the G41 command do you just put the tool radius following
> like this G41 .0625?
>
Discussion Thread
ballendo@y...
2000-09-02 14:30:30 UTC
Re:Gcode
Alan Marconett KM6VV
2000-09-02 16:20:48 UTC
Re:Gcode
ballendo@y...
2000-09-02 17:55:53 UTC
Re:Gcode
Alan Marconett KM6VV
2000-09-02 22:13:41 UTC
Re:Gcode
ballendo@y...
2000-09-02 22:53:04 UTC
Re:Gcode
Alan Marconett KM6VV
2000-09-03 14:44:39 UTC
Re:Gcode
Hugh Currin
2000-09-03 14:46:07 UTC
Re: [CAD_CAM_EDM_DRO] Re:Gcode
Alan Marconett KM6VV
2000-09-03 15:01:42 UTC
Re:Gcode
ballendo@y...
2000-09-03 18:43:47 UTC
Re:Gcode
ballendo@y...
2000-09-03 18:51:19 UTC
Re:Gcode
ballendo@y...
2000-09-03 20:13:39 UTC
Re: Re:Gcode
Gene
2002-06-05 13:47:36 UTC
Gcode
James Stevens
2002-06-05 14:03:16 UTC
Re: [CAD_CAM_EDM_DRO] Gcode
Jon Elson
2002-06-05 16:55:17 UTC
Re: [CAD_CAM_EDM_DRO] Gcode
bjammin@i...
2002-06-06 04:37:12 UTC
Re: [CAD_CAM_EDM_DRO] Gcode
robert charles weiss
2002-06-06 14:48:06 UTC
Re: [CAD_CAM_EDM_DRO] Gcode
andrewyslee
2002-06-06 18:04:10 UTC
Re: Gcode
doug98105
2002-06-06 20:10:36 UTC
Re: Gcode
Jon Elson
2002-06-06 22:26:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gcode
remy
2003-11-13 15:58:21 UTC
Gcode
Torsten
2003-11-13 17:43:24 UTC
Re: Gcode