Re: [CAD_CAM_EDM_DRO] Gcode
Posted by
Jon Elson
on 2002-06-05 16:55:17 UTC
Gene wrote:
On most controls, there is a "tool table" that has length and diameter values
for a number of tools. Most CNC controls use some function like
G41 D04 to tell it to use the diameter of tool #4 for this cutter offset.
You also have to give a lead-in linear move (some controls will also
accept an arc move) during which the move is interpolated in. The move
generally must be longer than the cutter radius, and also must not cause
a concave inside corner. This is tricky, and I have to lay it out on the
cad drawing to get it right. A similar lead-out move is required at
the end of the compensated section.
Jon
> When you use the G41 command do you just put the tool radius followingOn what control? It makes a difference.
> like this G41 .0625?
On most controls, there is a "tool table" that has length and diameter values
for a number of tools. Most CNC controls use some function like
G41 D04 to tell it to use the diameter of tool #4 for this cutter offset.
You also have to give a lead-in linear move (some controls will also
accept an arc move) during which the move is interpolated in. The move
generally must be longer than the cutter radius, and also must not cause
a concave inside corner. This is tricky, and I have to lay it out on the
cad drawing to get it right. A similar lead-out move is required at
the end of the compensated section.
Jon
Discussion Thread
ballendo@y...
2000-09-02 14:30:30 UTC
Re:Gcode
Alan Marconett KM6VV
2000-09-02 16:20:48 UTC
Re:Gcode
ballendo@y...
2000-09-02 17:55:53 UTC
Re:Gcode
Alan Marconett KM6VV
2000-09-02 22:13:41 UTC
Re:Gcode
ballendo@y...
2000-09-02 22:53:04 UTC
Re:Gcode
Alan Marconett KM6VV
2000-09-03 14:44:39 UTC
Re:Gcode
Hugh Currin
2000-09-03 14:46:07 UTC
Re: [CAD_CAM_EDM_DRO] Re:Gcode
Alan Marconett KM6VV
2000-09-03 15:01:42 UTC
Re:Gcode
ballendo@y...
2000-09-03 18:43:47 UTC
Re:Gcode
ballendo@y...
2000-09-03 18:51:19 UTC
Re:Gcode
ballendo@y...
2000-09-03 20:13:39 UTC
Re: Re:Gcode
Gene
2002-06-05 13:47:36 UTC
Gcode
James Stevens
2002-06-05 14:03:16 UTC
Re: [CAD_CAM_EDM_DRO] Gcode
Jon Elson
2002-06-05 16:55:17 UTC
Re: [CAD_CAM_EDM_DRO] Gcode
bjammin@i...
2002-06-06 04:37:12 UTC
Re: [CAD_CAM_EDM_DRO] Gcode
robert charles weiss
2002-06-06 14:48:06 UTC
Re: [CAD_CAM_EDM_DRO] Gcode
andrewyslee
2002-06-06 18:04:10 UTC
Re: Gcode
doug98105
2002-06-06 20:10:36 UTC
Re: Gcode
Jon Elson
2002-06-06 22:26:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gcode
remy
2003-11-13 15:58:21 UTC
Gcode
Torsten
2003-11-13 17:43:24 UTC
Re: Gcode