CAD CAM EDM DRO - Yahoo Group Archive

Re: deskWinNC camtronics limit switches

Posted by afogassa
on 2002-06-12 21:38:03 UTC
--- In CAD_CAM_EDM_DRO@y..., "andrewyslee" <andrewlee@s...> wrote:
> Hi,
>
> You guys had been a big help when I needed to get that offending
> Molex pin out, and with your suggestions, I managed to get it out
> with just the refill (ink reservoir) of a discarded ball-point pen!
> While not exactly rocket science, it is useful practical knowledge
> and skills. Thanks.
>
> Now I am going to try to connect limit/home switches. Camtronics 2A
> kit instructions says to refer to the software manual. DeskWinNC
help
> file say to use NO switches, no mention of whether pull-up
resistors
> are needed, which I interprete to mean none are needed. Before I
> start wiring it up, hope to hear the experiences of those who have
> wired up home/limit switches to their DeskWinNC-Camtronics
> combinations or even other combinations, which will be helpful
> background knowledge. Need to bring my confidence level up so I
don't
> have wrinkles on my brow when I power up the drives with the limit
> switches connected.
>
> Thanks
>
> Andrew

No pull up needed, the camtronic's board has it built in(the old
boards)
Buy a switch with both options N/O N/A deskwinnc firmware 1.19 was
N/O (I think) the 1.25 is N/A or vice versa.

Discussion Thread

john@x... 1999-06-08 14:57:53 UTC unsubscribe GeorgeMU@x... 1999-06-10 07:46:52 UTC unsubscribe Russell Dunn 1999-06-10 16:52:00 UTC Re: unsubscribe L/M Crocker 1999-06-11 09:24:15 UTC unsubscribe Ron Coelho 1999-06-22 08:04:18 UTC unsubscribe Carl Fiorletta 1999-11-12 10:56:56 UTC unsubscribe Darrell Gehlsen 1999-11-12 11:32:52 UTC Re: unsubscribe Arnold & Diane Chord 1999-12-06 09:55:19 UTC unsubscribe John Keane 2000-02-02 19:46:43 UTC unsubscribe WJJIM@a... 2000-10-12 18:03:51 UTC unsubscribe wbhinkle@a... 2001-04-24 14:05:57 UTC unsubscribe josh lane 2002-06-11 08:10:16 UTC unsubscribe andrewyslee 2002-06-11 08:36:50 UTC extracting pins economically John Brautlacht 2002-06-11 08:53:34 UTC Re: [CAD_CAM_EDM_DRO] extracting pins economically RichD 2002-06-11 09:30:48 UTC Re: [CAD_CAM_EDM_DRO] extracting pins economically beer@s... 2002-06-11 10:11:43 UTC Re: extracting pins economically Jon Elson 2002-06-11 10:44:30 UTC Re: [CAD_CAM_EDM_DRO] extracting pins economically Alan Marconett KM6VV 2002-06-11 10:57:48 UTC Re: [CAD_CAM_EDM_DRO] extracting pins economically wanliker@a... 2002-06-11 15:36:11 UTC Re: [CAD_CAM_EDM_DRO] extracting pins economically JanRwl@A... 2002-06-11 16:13:18 UTC Re: [CAD_CAM_EDM_DRO] extracting pins economically JanRwl@A... 2002-06-11 16:28:17 UTC Re: [CAD_CAM_EDM_DRO] extracting pins economically turbulatordude 2002-06-11 19:54:36 UTC Re: extracting pins economically andrewyslee 2002-06-12 13:09:48 UTC Re: extracting pins economically John Brautlacht 2002-06-12 13:14:57 UTC Re: [CAD_CAM_EDM_DRO] Re: extracting pins economically andrewyslee 2002-06-12 16:32:48 UTC deskWinNC camtronics limit switches afogassa 2002-06-12 21:38:03 UTC Re: deskWinNC camtronics limit switches andrewyslee 2002-06-14 20:45:15 UTC home switch vs limit switch Garry & Maxine Foster 2002-06-14 21:47:40 UTC Re: [CAD_CAM_EDM_DRO] home switch vs limit switch Alan Marconett KM6VV 2002-06-14 21:52:13 UTC Re: [CAD_CAM_EDM_DRO] home switch vs limit switch Brian 2002-06-15 03:11:44 UTC Re: [CAD_CAM_EDM_DRO] home switch vs limit switch P. J. Hicks 2002-09-13 19:04:33 UTC unsubscribe Howard Bailey 2002-10-11 14:13:00 UTC unsubscribe Tim Goldstein 2002-10-11 14:18:22 UTC Re: [CAD_CAM_EDM_DRO] unsubscribe Vanja Bubic 2002-10-29 05:51:12 UTC unsubscribe Hong Tuong 2004-11-10 03:40:04 UTC unsubscribe nielsenbe@a... 2007-02-02 15:22:15 UTC unsubscribe John Stevenson 2007-02-02 16:31:18 UTC Re: unsubscribe