Re: Bridgeport Boss 4 /Remex tape reader
Posted by
wantulok
on 2002-07-12 10:28:25 UTC
--- In CAD_CAM_EDM_DRO@y..., "evelle97530" <evelle97530@y...> wrote:
marked local and remote. You can hook a pc up to the local port,
and send the machine NC code once you put it in edit mode from the
user panel. On the boss 5, there is a bank of dip switches on the
card that connects to the ports. This bank has 8 switches that
control baud rate, 4 switches for each port. I think max baud is
19200. Using a program like bobcad, you can send your nc code
directly to the machine. The bauds must match, and to get that to
happen, you may have to experiment some. The boss5 echos question
marks (?) when it doesnt understand.
Once the code downloads properly, you need to hit the clear toggle
switch, and the machine should be ready to cut.
Hope this helps.
> I purchased a beautiful,low hour mill,but now I have to figure outcontrol,1
> how to make it purrrrr.It has 2 ribbons coming out of the
> connects to a bundle of blue wires that go to the 'x' card,Icontrol
> think,and 1 goes to the tape reader,I sincerely believe...The
> has 2 ports in front ,as well.They are round ,and I heard theywere
> actually the rs232 hookup ports(one of them).I have Mastercam,andthe
> machine is powered by a Teco /Westinghouse freq drive.I am notTHAT
> dumb,but I have an excuse...My mommy dropped me when a hot chipgot
> caught in her collar.Now this was a LONG time ago,before theIf the boss4 is anything like the boss 5, it has 2 rs232 ports,
> laws,but......
marked local and remote. You can hook a pc up to the local port,
and send the machine NC code once you put it in edit mode from the
user panel. On the boss 5, there is a bank of dip switches on the
card that connects to the ports. This bank has 8 switches that
control baud rate, 4 switches for each port. I think max baud is
19200. Using a program like bobcad, you can send your nc code
directly to the machine. The bauds must match, and to get that to
happen, you may have to experiment some. The boss5 echos question
marks (?) when it doesnt understand.
Once the code downloads properly, you need to hit the clear toggle
switch, and the machine should be ready to cut.
Hope this helps.
Discussion Thread
evelle97530
2002-07-12 07:43:57 UTC
Bridgeport Boss 4 /Remex tape reader
wantulok
2002-07-12 10:28:25 UTC
Re: Bridgeport Boss 4 /Remex tape reader
Jon Elson
2002-07-12 10:45:51 UTC
Re: [CAD_CAM_EDM_DRO] Bridgeport Boss 4 /Remex tape reader
doug king
2002-07-12 12:59:44 UTC
Re: [CAD_CAM_EDM_DRO] Bridgeport Boss 4 /Remex tape reader
doug king
2002-07-12 12:59:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Boss 4 /Remex tape reader
wantulok
2002-07-12 13:29:38 UTC
Re: Bridgeport Boss 4 /Remex tape reader
doug king
2002-07-12 13:38:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Boss 4 /Remex tape reader
Keith Bowers
2002-07-12 14:21:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Boss 4 /Remex tape reader
Jon Elson
2002-07-12 23:51:41 UTC
Re: [CAD_CAM_EDM_DRO] Bridgeport Boss 4 /Remex tape reader