Re: [CAD_CAM_EDM_DRO] Re: Bridgeport Boss 4 /Remex tape reader

Luckily,I'm weird...It looks like the port(on the front of the controller) has numbers on the pin holes,ceptin' maybe the middle 2...Would these numbers be a standard?Where I could count on them to be suchnsuch?I'm comin' off my computer with a db9 I hear tell only 3 wires are required for com.Thank You!!Doug
wantulok <joe@...> wrote: --- In CAD_CAM_EDM_DRO@y..., doug king wrote:

>
> Thanks,Joe.Now.How do I know which line is which on the local

port?I am getting 6 conductor rs232 line,and I know how to hook it
to my 'puter,but which line goes where on the port side?(on the
machine)Are they numbered corresponding to the numbers like on a
db25?Thanks!

> wantulok wrote: --- In

CAD_CAM_EDM_DRO@y..., "evelle97530" wrote:

> > I purchased a beautiful,low hour mill,but now I have to figure

out

> > how to make it purrrrr.It has 2 ribbons coming out of the
> control,1
> > connects to a bundle of blue wires that go to the 'x' card,I
> > think,and 1 goes to the tape reader,I sincerely believe...The
> control
> > has 2 ports in front ,as well.They are round ,and I heard they
> were
> > actually the rs232 hookup ports(one of them).I have

Mastercam,and

> the
> > machine is powered by a Teco /Westinghouse freq drive.I am not
> THAT
> > dumb,but I have an excuse...My mommy dropped me when a hot chip
> got
> > caught in her collar.Now this was a LONG time ago,before the
> > laws,but......
>
> If the boss4 is anything like the boss 5, it has 2 rs232 ports,
> marked local and remote. You can hook a pc up to the local port,
> and send the machine NC code once you put it in edit mode from the
> user panel. On the boss 5, there is a bank of dip switches on the
> card that connects to the ports. This bank has 8 switches that
> control baud rate, 4 switches for each port. I think max baud is
> 19200. Using a program like bobcad, you can send your nc code
> directly to the machine. The bauds must match, and to get that to
> happen, you may have to experiment some. The boss5 echos question
> marks (?) when it doesnt understand.
> Once the code downloads properly, you need to hit the clear toggle
> switch, and the machine should be ready to cut.
>
> Hope this helps.
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:

aol://5863:126/rec.crafts.metalworking or go thru Google.com to
reach it if you have trouble.

> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a

sister site to the CCED group, as many of the same members are
there, for OT subjects, that are not allowed on the CCED list.

>
>
>
> Post messages: CAD_CAM_EDM_DRO@y...
> Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> Moderator: jmelson@a... timg@k... [Moderator]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to

http://docs.yahoo.com/info/terms/

>
>
>
>
> ---------------------------------
> Do You Yahoo!?
> New! SBC Yahoo! Dial - 1st Month Free & unlimited access
>
> [Non-text portions of this message have been removed]

I have that info, but need to look it up. The hookup is kinda
weird. Let me get back to you.


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this as a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.



Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Mom
List Owner



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/




---------------------------------
Do You Yahoo!?
New! SBC Yahoo! Dial - 1st Month Free & unlimited access

[Non-text portions of this message have been removed]