CAD CAM EDM DRO - Yahoo Group Archive

Re: L298 goes boom - AWO?

Posted by tauscnc
on 2002-08-05 18:41:05 UTC
Hey Alan,
I started the post and have gotten some very good feedback. Seems
there are some different viewpoints on EMF and unplugging motors with
the power on. For me, I'll just turn the power off :)

NOW::: can you unplug the motors if you have the AWO feautre on? The
motors are already free? OR is this still an "EMF" problem?

Thanks for the idea on the switches but on the camtronics board there
is one AWO for all 3 axis (3 axis board) and another for the single
board. I either need to fully integrate the hook up through the 3
axis one to the single axis OR use one switch with two contacts (DTSP
I think??). I ordered the parts today from Mouser and hope to get my
goodies soon. Hope to have the camtronics boards working as flawless
as they where since I started tinkering with them :)

tauseef



--- In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> Hi Lee,
>
> I might have Re'd the wrong message. The fellow I was trying to
help
> had a Camtronics board. I was trying to extrapolate Mariss' fine
advice
> to Dan's fine board.
>
> I don't know WHO the originator of the message was now! Were you
also
> replying to a message? I'm lost!
>
> Alan KM6VV
>
>
> studleylee wrote:
> >
> > Hi Alan,
> > I've never used L297/298's. On my G210's I'm running 75vdc. With
> > 470uf Caps right at the supply pins of the G210.
> > -Lee
> >
> > -In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> > >Hi Lee,
> > >What motor voltage are you running? I think I recall 37V being
about
> > >the limit for L298's.And I recall Mariss saying that caps across
his
> > >Gecko's were needed if working near the max voltage.Perhaps this
> > >also applies to Dan's boards (see previous discussions on list)?
> > > HTH
> > > Alan KM6VV

Discussion Thread

tauscnc 2002-08-03 21:01:34 UTC L298 goes boom on my camtronics :( afogassa 2002-08-03 21:18:57 UTC Re: L298 goes boom on my camtronics :( RichD 2002-08-03 21:19:09 UTC Re: [CAD_CAM_EDM_DRO] L298 goes boom on my camtronics :( Carol & Jerry Jankura 2002-08-03 22:02:40 UTC RE: [CAD_CAM_EDM_DRO] Re: L298 goes boom on my camtronics :( tauscnc 2002-08-03 22:05:32 UTC Re: L298 goes boom on my camtronics :( RichD 2002-08-03 22:21:32 UTC Re: [CAD_CAM_EDM_DRO] Re: L298 goes boom on my camtronics :( tauscnc 2002-08-03 22:41:37 UTC Re: L298 goes boom on my camtronics :( Randy Gordon-Gilmore 2002-08-03 23:10:38 UTC Re: [CAD_CAM_EDM_DRO] Re: L298 goes boom on my camtronics :( tauscnc 2002-08-03 23:25:40 UTC Re: L298 goes boom on my camtronics :( alenz2002 2002-08-03 23:59:12 UTC Re: L298 goes boom on my camtronics :( bjammin@i... 2002-08-04 05:16:27 UTC Re: [CAD_CAM_EDM_DRO] L298 goes boom on my camtronics :( RichD 2002-08-04 07:57:43 UTC Re: [CAD_CAM_EDM_DRO] L298 goes boom on my camtronics :( tauscnc 2002-08-04 08:08:09 UTC Re: L298 goes boom on my camtronics :( bjammin@i... 2002-08-04 08:39:46 UTC L298 goes boom exeric1 2002-08-04 08:45:23 UTC Re: L298 goes boom on my camtronics :( exeric1 2002-08-04 09:09:31 UTC Re: L298 goes boom tauscnc 2002-08-04 09:53:57 UTC Re: L298 goes boom mayfieldtm 2002-08-04 10:22:36 UTC Re: L298 goes boom RichD 2002-08-04 12:25:20 UTC Re: [CAD_CAM_EDM_DRO] Re: L298 goes boom tauscnc 2002-08-04 12:49:53 UTC Re: L298 goes boom Alan Marconett KM6VV 2002-08-04 14:49:46 UTC Re: L298 goes boom on my camtronics :( Alan Marconett KM6VV 2002-08-04 15:17:14 UTC Re: L298 goes boom on my camtronics :( turbulatordude 2002-08-04 15:20:27 UTC Novice question about - Re: L298 goes boom studleylee 2002-08-04 16:37:48 UTC Re: L298 goes boom Alan Marconett KM6VV 2002-08-04 16:50:24 UTC Re: L298 goes boom studleylee 2002-08-04 17:29:10 UTC Re: L298 goes boom Alan Marconett KM6VV 2002-08-05 10:55:57 UTC Re: L298 goes boom bjammin@i... 2002-08-05 12:39:57 UTC boom mayfieldtm 2002-08-05 12:53:15 UTC Re: boom Bevan Weiss 2002-08-05 18:10:17 UTC re: boom tauscnc 2002-08-05 18:41:05 UTC Re: L298 goes boom - AWO? mayfieldtm 2002-08-05 23:05:54 UTC Re: boom bjammin@i... 2002-08-06 03:57:52 UTC Re: [CAD_CAM_EDM_DRO] re: boom Carol & Jerry Jankura 2002-08-06 05:46:35 UTC RE: [CAD_CAM_EDM_DRO] re: boom mayfieldtm 2002-08-06 08:44:56 UTC Re: boom kooloosj 2002-08-07 02:10:28 UTC Re: L298 goes boom on my camtronics :( Ian W. Wright 2002-08-07 10:25:15 UTC Re: [CAD_CAM_EDM_DRO] Re: L298 goes boom on my camtronics :( tauscnc 2002-08-08 18:48:21 UTC Re: L298 goes boom ( It's Fixed!- Yeah! ) afogassa 2002-08-08 20:51:42 UTC Re: L298 goes boom ( It's Fixed!- Yeah! ) Dave Hylands 2002-08-08 20:57:06 UTC RE: [CAD_CAM_EDM_DRO] Re: L298 goes boom ( It's Fixed!- Yeah! ) tauscnc 2002-08-08 21:06:06 UTC Re: L298 goes boom ( It's Fixed!- Yeah! ) tauscnc 2002-08-08 21:10:41 UTC Re: L298 goes boom ( It's Fixed!- Yeah! ) jeffgnu 2002-08-08 21:42:45 UTC Re: L298 goes boom ( It's Fixed!- Yeah! ) RichD 2002-08-08 21:51:40 UTC Re: [CAD_CAM_EDM_DRO] Re: L298 goes boom ( It's Fixed!- Yeah! ) RichD 2002-08-08 21:55:41 UTC Re: [CAD_CAM_EDM_DRO] Re: L298 goes boom ( It's Fixed!- Yeah! ) jeffgnu 2002-08-08 22:33:46 UTC Re: L298 goes boom ( It's Fixed!- Yeah! ) Ian W. Wright 2002-08-09 00:59:59 UTC Re: [CAD_CAM_EDM_DRO] Re: L298 goes boom ( It's Fixed!- Yeah! ) cadcambee 2002-08-09 01:10:02 UTC Re: L298 goes boom ( It's Fixed!- Yeah! ) caudlet 2002-08-09 08:00:15 UTC Re: L298 goes boom ( It's Fixed!- Yeah! ) cadcambee 2002-08-09 11:51:28 UTC Re: L298 goes boom (AWO) JJ 2002-08-11 11:37:48 UTC RE: [CAD_CAM_EDM_DRO] Re: L298 goes boom ( It's Fixed!- Yeah! )