Re: Re: Need Zero Help!!
Posted by
Ray Henry
on 2002-09-12 16:41:53 UTC
Ed, Alan
If you do not have home switches and are running with those pins closed
in your ini file, you can just hit home for each axis when you get where
you want 0.00 to be.
I'd use the script named Set_Coordinates that is under the scripts menu
in themc. It has teach for all axes that you have defined. If you leave
g54 alone and use g55 for your first coordinate system you can switch
between by just placing a g54 or g55 in the starting block where you want
the change to be active.
If you are going to use g92, don't forget g92.1, g92.2 and g92.3. I
described the effects of each of these on my grizz in a paper that is
available in the dropbox at www.linuxcnc.org. It's available in three
formats
g92test1.lyx
g92test1.pdf
g92test1.ps
Using this code can be a bit tricky.
Hope this helps (not zero help)
Ray
If you do not have home switches and are running with those pins closed
in your ini file, you can just hit home for each axis when you get where
you want 0.00 to be.
I'd use the script named Set_Coordinates that is under the scripts menu
in themc. It has teach for all axes that you have defined. If you leave
g54 alone and use g55 for your first coordinate system you can switch
between by just placing a g54 or g55 in the starting block where you want
the change to be active.
If you are going to use g92, don't forget g92.1, g92.2 and g92.3. I
described the effects of each of these on my grizz in a paper that is
available in the dropbox at www.linuxcnc.org. It's available in three
formats
g92test1.lyx
g92test1.pdf
g92test1.ps
Using this code can be a bit tricky.
Hope this helps (not zero help)
Ray
> From: Alan Marconett KM6VV <KM6VV@...>
> Subject: Re: Need Zero Help!!
>
> Hi Ed,
>
> Have you tried a "G92 X0 Y0 Z0" MDI command?
>
> Alan KM6VV
>
> EdFanta wrote:
> >
> > Hope I'm not the zero here. I got EMC up and running finally and
> > cannot seem to figure out how to set the readouts to zero. If I'm
> > edge finding the corner of my vise I need to set zero. It's probably
> > so obvious that I can't see it. Thanks. Ed.
> >
Discussion Thread
EdFanta
2002-09-12 14:57:36 UTC
Need Zero Help!!
Alan Marconett KM6VV
2002-09-12 15:03:02 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
EdFanta
2002-09-12 15:19:16 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Tim Goldstein
2002-09-12 15:37:48 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Ray Henry
2002-09-12 16:41:53 UTC
Re: Re: Need Zero Help!!
Les Watts
2002-09-12 17:33:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Need Zero Help!!
Jon Elson
2002-09-12 22:11:17 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Dave Engvall
2002-09-12 23:11:06 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Alan Marconett KM6VV
2002-09-13 00:16:04 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Ray Henry
2002-09-13 13:04:39 UTC
Re: Re: Re: Re: Need Zero Help!!
Ray Henry
2002-09-13 13:13:53 UTC
Re: Re: Need Zero Help!!
Jon Elson
2002-09-13 16:29:33 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!