Re: [CAD_CAM_EDM_DRO] Re: Re: Need Zero Help!!
Posted by
Les Watts
on 2002-09-12 17:33:07 UTC
Tim, Ray,Ed, Allen,
I have been running with Ray's suggested change to the .ini file
as follows:
RS274NGC_STARTUP_CODE = G20 G92.3
So far I seemed to have had one episode where saved parameters
were not displayed on startup, but most times everything works
perfectly. The one episode I would actually discount because I
didn't write down what the sequence of events were. It might have been
a mistake I made.I will try to log down things better in the future.
I am still doing a quick MDI command to confirm g92 status
before I start a program because the offsets are not shown
in the main coordinate position display.
Actually right now I am working more with carving things! Tonight
I am trying to correct the grammar in a 30 line poem to be carved
by EMC in a cedar plaque. Cemetery work.I am charging $50 per square foot.
So I was doing some C code this morning, and poetry now!
Oh well I had a couple composition and literature courses before
engineering school. I wish the poem was in c though!
Les
Leslie Watts
L M Watts Furniture
Tiger, Georgia USA
http://www.alltel.net/~leswatts/wattsfurniturewp.html
engineering page:
http://www.alltel.net/~leswatts/shop.html
I have been running with Ray's suggested change to the .ini file
as follows:
RS274NGC_STARTUP_CODE = G20 G92.3
So far I seemed to have had one episode where saved parameters
were not displayed on startup, but most times everything works
perfectly. The one episode I would actually discount because I
didn't write down what the sequence of events were. It might have been
a mistake I made.I will try to log down things better in the future.
I am still doing a quick MDI command to confirm g92 status
before I start a program because the offsets are not shown
in the main coordinate position display.
Actually right now I am working more with carving things! Tonight
I am trying to correct the grammar in a 30 line poem to be carved
by EMC in a cedar plaque. Cemetery work.I am charging $50 per square foot.
So I was doing some C code this morning, and poetry now!
Oh well I had a couple composition and literature courses before
engineering school. I wish the poem was in c though!
Les
Leslie Watts
L M Watts Furniture
Tiger, Georgia USA
http://www.alltel.net/~leswatts/wattsfurniturewp.html
engineering page:
http://www.alltel.net/~leswatts/shop.html
----- Original Message -----
From: "Ray Henry" <rehenry@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, September 12, 2002 7:42 PM
Subject: [CAD_CAM_EDM_DRO] Re: Re: Need Zero Help!!
>
> Ed, Alan
>
> If you do not have home switches and are running with those pins closed
> in your ini file, you can just hit home for each axis when you get where
> you want 0.00 to be.
>
> I'd use the script named Set_Coordinates that is under the scripts menu
> in themc. It has teach for all axes that you have defined. If you leave
> g54 alone and use g55 for your first coordinate system you can switch
> between by just placing a g54 or g55 in the starting block where you want
> the change to be active.
>
> If you are going to use g92, don't forget g92.1, g92.2 and g92.3. I
> described the effects of each of these on my grizz in a paper that is
> available in the dropbox at www.linuxcnc.org. It's available in three
> formats
Discussion Thread
EdFanta
2002-09-12 14:57:36 UTC
Need Zero Help!!
Alan Marconett KM6VV
2002-09-12 15:03:02 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
EdFanta
2002-09-12 15:19:16 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Tim Goldstein
2002-09-12 15:37:48 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Ray Henry
2002-09-12 16:41:53 UTC
Re: Re: Need Zero Help!!
Les Watts
2002-09-12 17:33:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Need Zero Help!!
Jon Elson
2002-09-12 22:11:17 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Dave Engvall
2002-09-12 23:11:06 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Alan Marconett KM6VV
2002-09-13 00:16:04 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!
Ray Henry
2002-09-13 13:04:39 UTC
Re: Re: Re: Re: Need Zero Help!!
Ray Henry
2002-09-13 13:13:53 UTC
Re: Re: Need Zero Help!!
Jon Elson
2002-09-13 16:29:33 UTC
Re: [CAD_CAM_EDM_DRO] Need Zero Help!!