Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Posted by
Jon Elson
on 2002-09-24 19:56:28 UTC
Kayla Sanders wrote:
to the wires. Making a special cable with individual twisted pairs for each
signal like step and direction will healp greatly. If your drivers have
opto-isolated inputs, this is all you should need.
In fact, that could damage them, and would certainly cause them to malfunction.
There is a small resistor that is used on most of them to set the motor current.
The Gecko does the current limiting.
Jon
> well would it be possible then to make my own cables and hook themInsulated? No, insulation does not prevent interfering signals from getting
> up to a parellel port connector ,and then run them to the drivers as
> long as each wire was insulated well against any external
> interference?
to the wires. Making a special cable with individual twisted pairs for each
signal like step and direction will healp greatly. If your drivers have
opto-isolated inputs, this is all you should need.
> also, is it going to hurt the geckos if i use a 24Vdc/12A powerYou do NOT need a resistor in the DC power lines to the Gecko drives.
> supply? am igoing to have to use a current limiting resister from
> power to the drivers or does the gecko do this for me??
In fact, that could damage them, and would certainly cause them to malfunction.
There is a small resistor that is used on most of them to set the motor current.
The Gecko does the current limiting.
Jon
Discussion Thread
Kayla Sanders
2002-09-24 12:23:51 UTC
cable from PC to stepper drivers?????
caudlet
2002-09-24 15:03:37 UTC
Re: cable from PC to stepper drivers?????
Tim Goldstein
2002-09-24 15:11:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Kayla Sanders
2002-09-24 16:00:41 UTC
Re: cable from PC to stepper drivers?????
Alan Marconett KM6VV
2002-09-24 16:29:59 UTC
Re: cable from PC to stepper drivers?????
cadcamcenter
2002-09-24 17:28:53 UTC
Re: cable from PC to stepper drivers?????
Marv Frankel
2002-09-24 18:30:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Jerry Kimberlin
2002-09-24 18:42:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Jon Elson
2002-09-24 19:49:33 UTC
Re: [CAD_CAM_EDM_DRO] cable from PC to stepper drivers?????
Jon Elson
2002-09-24 19:56:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Tim Goldstein
2002-09-24 20:03:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Jon Elson
2002-09-24 20:04:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Jon Elson
2002-09-24 20:10:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Mark
2002-09-24 20:51:15 UTC
Re: cable from PC to stepper drivers?????
dazedNconfused
2002-09-24 21:12:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????
Mark
2002-09-24 21:19:48 UTC
Re: cable from PC to stepper drivers?????
Marv Frankel
2002-09-25 06:07:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: cable from PC to stepper drivers?????