RE: [CAD_CAM_EDM_DRO] Re: Screw drive
Posted by
Miroslav Pejic
on 2003-03-29 04:40:18 UTC
Hi Alex,
I assume 3 short screws must be with axial/radial bearings, and I think any
contaminent can be easy "filtered" with some pieces of textile
Maybe yoy can scan the picture form the magazine menitioned, then upload to
forum?
Peja
-----Original Message-----
From: Torsten Kammerer [mailto:torsten@...]
Sent: Friday, March 28, 2003 11:43 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: Screw drive
I assume 3 short screws must be with axial/radial bearings, and I think any
contaminent can be easy "filtered" with some pieces of textile
Maybe yoy can scan the picture form the magazine menitioned, then upload to
forum?
Peja
-----Original Message-----
From: Torsten Kammerer [mailto:torsten@...]
Sent: Friday, March 28, 2003 11:43 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: Screw drive
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "alex" <telecomt@t...> wrote:
> OK,
> just loaded the scetch into file section.
> Called screwdrive .jpg.
> Let me know if you have questions.
> Regards, Alex
> ----- Original Message -----
> From: Dantrol <dantrol@o...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Friday, March 28, 2003 8:46 AM
> Subject: [CAD_CAM_EDM_DRO] Re: Screw drive
>
>
> > Alex, I do not have easy access to the magazine. Is it possible
for you to
> better describe, or sketch, the "make-your-own" screw drive? Thanks.
> >
> > 3-27-03, alex, telecomt@t..., Screw drive
> > Yesterday I stumbled upon "Model Engineer's Workshop" magazine.
Besides
> other interesting staff there was an article on making your own
> > screw drive as a replacement for a ball screw. I'm amazed at how
easy and
> inexpensive is to make this kind of drive - basically its an
arrangement of
> three short screws, belonging to a nut, around the drive screw. One
short
> screw can be tightened to adjust the backlash. It looks like anyone
can make
> this kind of drive in a matter of hours. Cheap too.
Discussion Thread
alex
2003-03-27 08:25:22 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
Tony Jeffree
2003-03-27 08:34:04 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
alex
2003-03-27 14:53:36 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
Tony Jeffree
2003-03-27 15:27:13 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
alex
2003-03-27 15:38:36 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
Tony Jeffree
2003-03-27 15:55:18 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
Jason Cox
2003-03-27 16:02:44 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
alex
2003-03-27 16:19:47 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
JanRwl@A...
2003-03-27 18:45:14 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
Dantrol
2003-03-28 09:11:43 UTC
Re: Screw drive
alex
2003-03-28 09:35:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Screw drive
alex
2003-03-28 12:42:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Screw drive
vrsculptor
2003-03-28 14:35:15 UTC
Re: Screw drive
Torsten Kammerer
2003-03-28 14:42:41 UTC
Re: Screw drive
Miroslav Pejic
2003-03-29 04:40:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: Screw drive
turbulatordude
2003-03-29 07:51:59 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
alex
2003-03-29 09:34:29 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
Tony Jeffree
2003-03-29 09:44:25 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
alex
2003-03-29 09:54:20 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive
alex
2003-03-29 13:48:54 UTC
Re: [CAD_CAM_EDM_DRO]Screw drive