Re: [CAD_CAM_EDM_DRO] MY 210 GECKO BURNED!!!!!!
Posted by
Harvey White
on 2003-04-21 08:18:35 UTC
On Mon, 21 Apr 2003 01:54:26 -0000, you wrote:
stops blowing.
That's the one that has the problem. Most likely, one of the
transistors in the driver has shorted, or perhaps both. Hard to say.
Disconnecting the motor would not make a difference, I think.
Harvey
>I bought 3 210 gecko months ago and I was very happy with them untilDisconnect each driver from the power and signal inputs until the fuse
>now. I do not use them very often. However, one of them stop working
>yesterday without reason since my current and volt are very low so
>they never get hot. this is my settings:
>
>power supply type: unregulated 35v 4amps
>resistor to limit the current: 18k (2 amp)
>4 wire steppers (2a each)
>
>when I power on driver the fuse in my cnc encloser which is 125v 5a
>keep burning is like the driver is in short or somelike and I do not
>understand how come it could happen if I do not use them very often
>and I heard that they are very drivers.the other two works fine
>without any problem.
>
stops blowing.
That's the one that has the problem. Most likely, one of the
transistors in the driver has shorted, or perhaps both. Hard to say.
Disconnecting the motor would not make a difference, I think.
Harvey
>Any suggestion???
>
>
>
>Luis
>
Discussion Thread
luisguillermo98
2003-04-20 18:54:28 UTC
MY 210 GECKO BURNED!!!!!!
Vince Negrete
2003-04-20 21:06:53 UTC
Re: [CAD_CAM_EDM_DRO] MY 210 GECKO BURNED!!!!!!
Harvey White
2003-04-21 08:18:35 UTC
Re: [CAD_CAM_EDM_DRO] MY 210 GECKO BURNED!!!!!!
luisguillermo98
2003-04-21 18:17:30 UTC
Re: MY 210 GECKO BURNED!!!!!!
JanRwl@A...
2003-04-21 18:22:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: MY 210 GECKO BURNED!!!!!!
turbulatordude
2003-04-21 19:23:54 UTC
Re: MY 210 GECKO BURNED!!!!!!
Harvey White
2003-04-21 21:15:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: MY 210 GECKO BURNED!!!!!!
caudlet
2003-04-21 21:32:13 UTC
Re: MY 210 GECKO BURNED!!!!!!
Jon Elson
2003-04-21 22:56:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: MY 210 GECKO BURNED!!!!!!
JanRwl@A...
2003-04-22 14:34:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: MY 210 GECKO BURNED!!!!!!
luisguillermo98
2003-04-22 17:58:40 UTC
Re: MY 210 GECKO BURNED!!!!!!
luisguillermo98
2003-04-22 18:03:51 UTC
Re: MY 210 GECKO BURNED!!!!!!
Harvey White
2003-04-22 21:20:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: MY 210 GECKO BURNED!!!!!!
William Scalione
2003-04-22 21:39:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: MY 210 GECKO BURNED!!!!!!
turbulatordude
2003-04-23 02:21:15 UTC
Re: MY 210 GECKO BURNED!!!!!!