Re: Stepper Motor Power supply Sizing.
Posted by
Mariss Freimanis
on 2003-05-29 10:29:16 UTC
Peter,
Bob has the right answer, it is 2.66A for a 4A rated motor. That will
be the maximum supply current which occurs when the motor is turning
at high speed and is loaded to just short of stalling. Other
conditions will draw substantially less supply current.
Mariss
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Peter Homann"
<peter.homann@a...> wrote:
Bob has the right answer, it is 2.66A for a 4A rated motor. That will
be the maximum supply current which occurs when the motor is turning
at high speed and is loaded to just short of stalling. Other
conditions will draw substantially less supply current.
Mariss
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Peter Homann"
<peter.homann@a...> wrote:
> Hi,where it
>
> I have been looking at Marriss's White paper on Power Supply's
> states that the current requirements for a stepper motor is 2/3 ofthe
> motors rated current in Parallel and 1/3 when in series.parallel, is
>
> So, If I have a 4ohm, 4A/phase 8 wire stepper and I wire it in
> the current requirements for the motor 4*2/3 = 2.66A or is it2*2.66 =
> 5.333A as the motor has 2 phases.
>
> Thanks,
>
>
> Peter Homann
> mailto:Peter.Homann@a...
> Adacel Technologies Limited,
> 250 Bay St, BRIGHTON, 3186, AUSTRALIA
> http://www.adacel.com <http://www.adacel.com>
> Telephone +61 (3) 8530 7777, Facsimile +61 (3) 9596 2960
> Mobile 0421-601 665
Discussion Thread
wanliker@a...
2003-05-28 13:21:00 UTC
Estop
wanliker@a...
2003-05-28 13:43:10 UTC
Estop
Jon Elson
2003-05-28 22:24:07 UTC
Re: [CAD_CAM_EDM_DRO] Estop
Peter Homann
2003-05-28 22:52:02 UTC
Stepper Motor Power supply Sizing.
Robert Campbell
2003-05-29 06:23:10 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply Sizing.
wanliker@a...
2003-05-29 06:30:45 UTC
Re: [CAD_CAM_EDM_DRO] Estop
Dan Symonds - ATT
2003-05-29 08:12:42 UTC
RE: [CAD_CAM_EDM_DRO] Estop
turbulatordude
2003-05-29 08:34:42 UTC
Re: Estop
Jon Elson
2003-05-29 10:06:12 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply Sizing.
jeffalanp
2003-05-29 10:07:55 UTC
Re: Stepper Motor Power supply Sizing.
Jon Elson
2003-05-29 10:18:30 UTC
Re: [CAD_CAM_EDM_DRO] Estop
turbulatordude
2003-05-29 10:24:33 UTC
Re: Estop
Mariss Freimanis
2003-05-29 10:29:16 UTC
Re: Stepper Motor Power supply Sizing.
Harvey White
2003-05-29 11:51:19 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply Sizing.
wanliker@a...
2003-05-29 13:34:51 UTC
Re: [CAD_CAM_EDM_DRO] Estop
JanRwl@A...
2003-05-29 13:55:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Power supply Sizing.
turbulatordude
2003-05-29 18:33:55 UTC
Re: Stepper Motor Power supply Sizing.
Mariss Freimanis
2003-05-29 19:28:28 UTC
Re: Stepper Motor Power supply Sizing.
JanRwl@A...
2003-05-29 21:30:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Power supply Sizing.
turbulatordude
2003-05-30 06:58:22 UTC
Re: Stepper Motor Power supply Sizing.
JanRwl@A...
2003-05-30 09:31:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Power supply Sizing.
turbulatordude
2003-05-30 18:03:50 UTC
Re: Stepper Motor Power supply Sizing.
JanRwl@A...
2003-05-30 18:08:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Power supply Sizing.
Raymond Heckert
2003-05-31 20:06:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Power supply Sizing.
JanRwl@A...
2003-05-31 20:21:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Power supply Sizing.
Harvey White
2003-05-31 23:22:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Stepper Motor Power supply Sizing.
R Petersen
2003-06-01 06:33:39 UTC
Stepper Motor Power supply.
Jerry Kimberlin
2003-06-01 09:03:57 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply.
JanRwl@A...
2003-06-01 12:24:33 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply.
R Petersen
2003-06-02 06:04:34 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply.
fortino
2003-06-02 08:00:26 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply.
caudlet
2003-06-02 12:25:17 UTC
Re: Stepper Motor Power supply.
JanRwl@A...
2003-06-02 13:11:40 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply.
Tony Jeffree
2003-06-02 13:17:29 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply.
John Guenther
2003-06-02 13:20:02 UTC
RE: [CAD_CAM_EDM_DRO] Stepper Motor Power supply.
JanRwl@A...
2003-06-02 14:20:08 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Power supply.