Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Posted by
Jon Elson
on 2003-06-12 21:30:50 UTC
Tom Benedict wrote:
down a G0 just like any other move with a feed rate override). I always
set the feedrate to 50% or even 10% when testing anything that has even
a small likelyhood of doing something undesired.
Unless this is some wierd effect of the G0, I don't know what the
problem is.
I just haven't seen this sort of thing on the EMC systems I'm using.
But, the
only BDI I have is quite old, so this may be a new quirk.
Jon
>That's exactly what I did. My edge finder has a 0.200" wide tip. So IThis is why I NEVER use G0 (although EMC seems to allow you to slow
>brought it up against the two edges, shifted it by +0.100 +0.100, and set
>that to x=0 y=0. I then switched to my tool, brought the tip down until
>it was kissing the top of the workpiece and set that to be z=0. In MDI, a
>G0X0Y0Z0 would always return the tool to that position. Which is why I
>was so suprised when a G0X0Y0Z0 in the program drove the tool straight
>into the work piece.
>
>I'm not talking about a small offset here. It buried the mill about 1"
>deep in the material before it snapped off.
>
>
down a G0 just like any other move with a feed rate override). I always
set the feedrate to 50% or even 10% when testing anything that has even
a small likelyhood of doing something undesired.
Unless this is some wierd effect of the G0, I don't know what the
problem is.
I just haven't seen this sort of thing on the EMC systems I'm using.
But, the
only BDI I have is quite old, so this may be a new quirk.
Jon
Discussion Thread
inetd_conf
2003-06-11 23:36:30 UTC
Question Re: Work Offsets
Fred Smith
2003-06-12 06:12:38 UTC
Question Re: Work Offsets
stephank97
2003-06-12 08:04:48 UTC
Question Re: Work Offsets
Jon Elson
2003-06-12 10:39:24 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Tim Goldstein
2003-06-12 11:02:05 UTC
RE: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Tom Benedict
2003-06-12 11:33:23 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Tom Benedict
2003-06-12 11:36:12 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Tom Benedict
2003-06-12 11:40:07 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Fred Smith
2003-06-12 11:43:13 UTC
Question Re: Work Offsets
Tim Goldstein
2003-06-12 12:12:22 UTC
RE: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Tom Benedict
2003-06-12 12:33:33 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Tom Benedict
2003-06-12 12:41:02 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Tim Goldstein
2003-06-12 13:06:20 UTC
RE: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Fred Smith
2003-06-12 15:06:45 UTC
Question Re: Work Offsets
Fred Smith
2003-06-12 15:07:23 UTC
Question Re: Work Offsets
Keith Rumley
2003-06-12 15:20:41 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Tom Benedict
2003-06-12 15:53:08 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Ray Henry
2003-06-12 18:27:23 UTC
Re: Re: Question Re: Work Offsets
LARRY ROBERTSON
2003-06-12 20:53:08 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Jon Elson
2003-06-12 21:16:26 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Jon Elson
2003-06-12 21:30:50 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Jon Elson
2003-06-12 21:38:09 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Jon Elson
2003-06-12 21:47:37 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Jon Elson
2003-06-12 21:57:28 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Jon Elson
2003-06-12 22:04:40 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Jon Elson
2003-06-12 22:16:03 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets
Michael Romeo
2003-06-12 22:26:32 UTC
Question Re: Work Offsets
Raymond Heckert
2003-06-13 17:48:30 UTC
Re: [CAD_CAM_EDM_DRO] Question Re: Work Offsets