CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] EMC questions

Posted by Tony Jeffree
on 2003-07-14 07:31:01 UTC
At 08:22 14/07/2003 -0600, you wrote:
> > "Stepper motor control is implemented using a second real-time task
> > that runs at 100 microseconds. This task writes the parallel port
> > output with bits set or cleared based on whether the a pulse should
> > be raised or lowered. This gives an effective period of 200
> > microseconds for a full up-and-down pulse, or a 5 kilohertz
> > frequency."
>
>Like much of EMC documentation you can not believe all that you read.
>This is not correct. I have EMC running with a pulse stream of 25
>kilohetz. It will actually go somewhat faster depending upon the speed
>of your system. For stepper use you can get the fastest rates with
>steppermod.o, but the pulse stream is not evenly paced. You will get a
>better pulse stream pacing with freqmod.o, but it take more system
>resources. On the system you are running either one of the motion tasks
>will give you a much higher rate than 5 Khz if you tune it properly.

Isn't it comforting to hear yet more evidence of how user-friendly EMC
is... ;-)


Regards,
Tony

Discussion Thread

L B Jareteg 2000-08-13 14:35:56 UTC EMC questions ajv2803959 2002-03-13 07:51:41 UTC EMC questions Tom Benedict 2002-03-13 07:59:14 UTC Re: [CAD_CAM_EDM_DRO] EMC questions Jon Elson 2002-03-13 10:02:18 UTC Re: [CAD_CAM_EDM_DRO] EMC questions Tim Goldstein 2002-03-13 21:15:57 UTC RE: [CAD_CAM_EDM_DRO] EMC questions Jon Elson 2002-03-13 23:08:56 UTC Re: [CAD_CAM_EDM_DRO] EMC questions ajv2803959 2002-03-15 03:08:45 UTC Re: EMC questions semenoff 2002-10-11 13:48:28 UTC EMC questions Tim Goldstein 2002-10-11 14:11:44 UTC Re: [CAD_CAM_EDM_DRO] EMC questions Jon Elson 2002-10-11 23:09:20 UTC Re: [CAD_CAM_EDM_DRO] EMC questions samcoinc2001 2003-07-14 00:09:27 UTC EMC questions Tim Goldstein 2003-07-14 07:22:13 UTC RE: [CAD_CAM_EDM_DRO] EMC questions Tony Jeffree 2003-07-14 07:31:01 UTC RE: [CAD_CAM_EDM_DRO] EMC questions Tim Goldstein 2003-07-14 07:43:03 UTC RE: [CAD_CAM_EDM_DRO] EMC questions sam sokolik 2003-07-14 09:09:04 UTC RE: [CAD_CAM_EDM_DRO] EMC questions Jon Elson 2003-07-14 10:09:53 UTC Re: [CAD_CAM_EDM_DRO] EMC questions wanliker@a... 2003-07-14 13:46:39 UTC Re: [CAD_CAM_EDM_DRO] EMC questions Markwayne 2003-07-15 12:42:10 UTC Re: [CAD_CAM_EDM_DRO] EMC questions vavaroutsos 2004-05-16 12:17:41 UTC EMC questions Derek B. 2004-05-16 18:47:58 UTC Rocky Mountain Model Engineering Show!