Re: Digitizer probe progress
Posted by
Wayne C. Gramlich
on 2003-09-25 21:10:40 UTC
Graham:
Every time I've looked at the digitizer.pdf file, I wind
shaking my head and saying "I don't get it!" I guess some
sort of electrical circuit is supposed to be made or broken,
but I can't figure out how the circuit is supposed to operate.
Could you explain where the wires are supposed to go, and
what causes the circuit to be completed/broken? Am I correct
in assuming that the goal of this digitizer probe is to
detect any deflection in X and Y and deflection in one
direction on Z? Any edification would be greatly appreciated.
Thanks in advance,
-Wayne
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Graham Stabler" <eexgs@n...>
wrote:
Every time I've looked at the digitizer.pdf file, I wind
shaking my head and saying "I don't get it!" I guess some
sort of electrical circuit is supposed to be made or broken,
but I can't figure out how the circuit is supposed to operate.
Could you explain where the wires are supposed to go, and
what causes the circuit to be completed/broken? Am I correct
in assuming that the goal of this digitizer probe is to
detect any deflection in X and Y and deflection in one
direction on Z? Any edification would be greatly appreciated.
Thanks in advance,
-Wayne
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Graham Stabler" <eexgs@n...>
wrote:
> Just a quick post to say that I have my digitizer probe working. It[snip]
> is based on the one in the files section drawn by Carlos Guillermo.
> The file is digitizer.pdf.
>
> Based on this I built the digitizer out of Delrin on my little
> Proxxon mill. I had been looking for 2mm ball bearings for the
> pivots and eventually got these from smallparts.com (shame about the
> $25 postage, grrr). The probe works really well although I am
> disappointed that I did not manage to get the probe part concentric
> with the shaft that is held by the mill collet. This means it is
> only good for digitizing rather than edge finding etc. I may rectify
> this in the future and it was a function of my workmanship rather
> than the design.
Discussion Thread
Graham Stabler
2003-09-24 13:31:08 UTC
Digitizer probe progress
Wayne C. Gramlich
2003-09-25 21:10:40 UTC
Re: Digitizer probe progress
Graham Stabler
2003-09-26 02:55:42 UTC
Re: Digitizer probe progress
ccq@x...
2003-09-26 07:08:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizer probe progress
Graham Stabler
2003-09-26 08:33:12 UTC
Re: Digitizer probe progress
tomp_tag
2003-09-27 07:24:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizer probe progress
Wayne C. Gramlich
2003-09-27 12:30:03 UTC
Re: Digitizer probe progress
Graham Stabler
2003-09-27 16:02:52 UTC
Re: Digitizer probe progress
washcomp
2003-09-28 07:31:19 UTC
Where should I head on a probe? (Was:Digitizer probe progress)
Fred Smith
2003-09-28 08:10:45 UTC
Re: Where should I head on a probe? (Was:Digitizer probe progress)
Tim Goldstein
2003-09-28 10:30:30 UTC
RE: [CAD_CAM_EDM_DRO] Re: Where should I head on a probe? (Was:Digitizer probe progress)
Fred Smith
2003-09-28 11:55:51 UTC
Re: Where should I head on a probe? (Was:Digitizer probe progress)
Tim Goldstein
2003-09-28 13:45:49 UTC
RE: [CAD_CAM_EDM_DRO] Re: Where should I head on a probe? (Was:Digitizer probe progress)
Graham Stabler
2003-09-28 15:56:15 UTC
Re: Where should I head on a probe? (Was:Digitizer probe progress)
Bob Bachman
2003-10-09 20:26:46 UTC
Generating a Sphere
Fred Smith
2003-10-09 21:00:15 UTC
Re: Generating a Sphere
doug98105
2003-10-09 22:11:11 UTC
Re: Generating a Sphere
Michael Milligan
2003-10-09 23:39:19 UTC
RE: [CAD_CAM_EDM_DRO] Generating a Sphere
Marcus and Eva
2003-10-10 08:05:37 UTC
Re: [CAD_CAM_EDM_DRO] Generating a Sphere
Elliot Burke
2003-10-10 12:56:07 UTC
RE: Generating a Sphere
Bob Bachman
2003-10-13 18:00:16 UTC
Re: [CAD_CAM_EDM_DRO] Generating a Sphere