Re: DYNA 2400 SOFTWARE
Posted by
jeff_birt2000
on 2003-09-25 19:30:06 UTC
I think I may have created some confusion with my last post by
talking about two diffrent types of software. The Firmware I
mentioned is in the form of two EPROM chips that must be purchased
from DynaMechatronics for $150.00. This is the software for a Dyna
2400c controller.
The second piece of software I talked about was DynaComm which is a
piece of software I'm writing to becom familiar with VB.NET and the
Dyna mill. DynaComm is in the public domain,I wrote it and you can
use it for free if you want to. It's basically a download / DNC
utility for a Dyna Mill or lathe, but the DNC part does not work yet.
As a matter of fact if anyone else has a mill or something that
accepts programs over a serial link and has the communication specs
I may even try and make it work for that too.
Sorry for the confusion.
Jeff Birt
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "jeff_birt2000"
<birt_j@e...> wrote:
talking about two diffrent types of software. The Firmware I
mentioned is in the form of two EPROM chips that must be purchased
from DynaMechatronics for $150.00. This is the software for a Dyna
2400c controller.
The second piece of software I talked about was DynaComm which is a
piece of software I'm writing to becom familiar with VB.NET and the
Dyna mill. DynaComm is in the public domain,I wrote it and you can
use it for free if you want to. It's basically a download / DNC
utility for a Dyna Mill or lathe, but the DNC part does not work yet.
As a matter of fact if anyone else has a mill or something that
accepts programs over a serial link and has the communication specs
I may even try and make it work for that too.
Sorry for the confusion.
Jeff Birt
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "jeff_birt2000"
<birt_j@e...> wrote:
>checksum
> I recieved the backup batteries from DyanMechtronics today and
> installed them. It made no apparent diffrent to the operation of
> Line Execute mode. I did find out from Dyna that a newer firmware
> level was available so I orderd it. Not cheap at $150. The
> of the version I had was 15fc and the latest for it is 4859.We'll
> see if it makes a difference.due
>
> I have posted DynaComm Version 1.1 in the files section. This
> verison includes an editing window for the CNC program and a few
> other cosmetic improvements. The Line execute is still disabled
> to my 2400 not working properly with it. Once again, you musthave
> the .NET frame work installed to run this program which is a freeexecute
> download from windowsupdate.com
>
> I also found out these Dyna controllers will run in a 'Block
> mode' which downloads untill a SKIP TO 900 is encounterd and thenand
> waits for the next block of code to be downloaded. There does not
> appear to be any handshaking between blocks so you have to wait
> then manually download the next block.mode
>
> Has anyone out there actually ran one of these in line execute
> correctly?<birt_j@e...>
>
> Jeff Birt
>
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "jeff_birt2000"
> wrote:are
> > David,
> >
> > I wound up ordering the batteries (the one in the dm3000 lath
> > controller was low too) from Dyna before seeing you note. They
> > $38.00 from Dyna.ARC
> >
> > I tried replacing the previous code to generate an arc with an
> > frame but have the same problem; it works great when the wholealso
> > program is downloaded but goes crazey in line execute mode. I
> > found some paperwork yesterday indicating there may be a 'Block
> > Execute mode' available with the correct firmware version. I'll
> call
> > Dyna and inquire.
> >
> > Jeff
Discussion Thread
mrdavidpontes
2003-09-12 23:32:44 UTC
DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-13 07:47:36 UTC
Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-13 23:36:12 UTC
Re: DYNA 2400 SOFTWARE
R Homer
2003-09-16 08:00:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-17 00:14:17 UTC
Re: DYNA 2400 SOFTWARE
bank haam
2003-09-17 00:14:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-17 00:15:10 UTC
Re: DYNA 2400 SOFTWARE
bank haam
2003-09-17 15:00:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-17 23:45:33 UTC
Re: DYNA 2400 SOFTWARE
bank haam
2003-09-18 11:42:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-19 06:59:20 UTC
Re: DYNA 2400 SOFTWARE
mrdavidpontes
2003-09-19 10:34:25 UTC
Re: DYNA 2400 SOFTWARE
bank haam
2003-09-20 07:56:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-23 06:01:59 UTC
Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-25 15:42:29 UTC
Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-25 19:30:06 UTC
Re: DYNA 2400 SOFTWARE
bank haam
2003-09-26 07:11:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-26 17:40:52 UTC
Re: DYNA 2400 SOFTWARE
mrdavidpontes
2003-09-26 23:36:49 UTC
Re: DYNA 2400 SOFTWARE
jeff_birt2000
2003-09-27 20:13:10 UTC
Re: DYNA 2400 SOFTWARE