re: comments on driver circuits
Posted by
turbulatordude
on 2003-11-20 09:17:26 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Harvey White <madyn@i...>
wrote:
can you elaborate on the filters ?
Dave
wrote:
> On Thu, 20 Nov 2003 06:20:28 -0600, you wrote:I want
>
> <snip>
>
> >Best regards
> >Hans Wedemeyer
> >PS This kind of crap distracts me and just delays my projects....
> >to finish the EAGLE layout for the L297/L298 and perhaps a 5 Ampdriver...
>fairly
> I found it helpful to put a few LEDs in the circuit to enable me to
> know how the circuit is doing, a bipolar red/green one across the
> motor coil leads. I also found the chopper current sense to be
> sensitive to spikes, so I added some optional filtering in thecurrent
> feedback loop from the sense resistor to the op amp. Those wereneeded.
> useful as well. I also added some power led indicators where
> Barely fit on the 3 by 4 inch single sided layout I used, but didfit.
>Hi Harvey,
> Harvey
can you elaborate on the filters ?
Dave
Discussion Thread
Vince Negrete
2003-11-20 03:25:28 UTC
Ignore it.. Was: eBay item. Description is not truthful
(no author)
2003-11-20 04:48:13 UTC
Re: [CAD_CAM_EDM_DRO] UPDATE Re: eBay item. Description is not truthful---
Harvey White
2003-11-20 08:59:23 UTC
Re: [CAD_CAM_EDM_DRO] UPDATE Re: eBay item. Description is not truthful---
turbulatordude
2003-11-20 09:17:26 UTC
re: comments on driver circuits
Harvey White
2003-11-20 09:42:17 UTC
Re: [CAD_CAM_EDM_DRO] re: comments on driver circuits
Raymond Gage
2003-11-20 10:00:13 UTC
Ball/Lead Screw mapping
Kim Lux
2003-11-20 11:57:52 UTC
Re: [CAD_CAM_EDM_DRO] Ball/Lead Screw mapping
Dan Mauch
2003-11-20 12:37:57 UTC
RE: [CAD_CAM_EDM_DRO] Ball/Lead Screw mapping
Kim Lux
2003-11-20 13:05:09 UTC
RE: [CAD_CAM_EDM_DRO] Ball/Lead Screw mapping
Jon Elson
2003-11-20 21:54:25 UTC
Re: [CAD_CAM_EDM_DRO] Ball/Lead Screw mapping
Kim Lux
2003-11-21 06:17:32 UTC
Re: [CAD_CAM_EDM_DRO] Ball/Lead Screw mapping
Ray Henry
2003-11-21 09:34:53 UTC
Re: Re: Ball/Lead Screw mapping
Jon Elson
2003-11-21 09:54:09 UTC
Re: [CAD_CAM_EDM_DRO] Ball/Lead Screw mapping
Jon Elson
2003-11-21 21:01:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Ball/Lead Screw mapping
Raymond Gage
2003-11-22 10:34:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Ball/Lead Screw mapping
Jon Elson
2003-11-22 17:17:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Ball/Lead Screw mapping
Ray Henry
2003-11-22 21:29:36 UTC
Re: Re: Re: Re: Ball/Lead Screw mapping