CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: SS Relays

on 2003-11-21 13:25:02 UTC
probably the easiest too, unless you've got a hundred or so rail mounted
24V relays (massive tool gloat...)

erie

Harvey White wrote:

>On Fri, 21 Nov 2003 15:03:23 -0000, you wrote:
>
>
>
>>Ah! I ran into this problem and couldn't figure out what was going on
>>for the life of me.
>>
>>
>
>Triacs and SCRs turn on, and stay on until either 1) the current drops
>below a set value (you can't set it), or the voltage reverses
>(reducing the current).
>
>Therefore, good only for AC or applications where there will be
>another way of turning off the current...
>
>
>
>>What type of relay do you use for switching DC?
>>
>>
>
>SSR, but one with an FET or bipolar transistor. A good cheap
>electromechanical relay is the headlight relay in a car. 12 volts in,
>30 amps capability.
>
>Harvey
>
>
>
>>Thanks,
>>Chris
>>
>>
>>
>>
>>>From: Mark Thompson
>>>
>>>Hi
>>>
>>>www.digikey.com is a great place to get most anything electronic.
>>>
>>>Most relays that are zero crossing are AC only (IE: Triac based).
>>>
>>>
>>So if
>>you are
>>
>>
>>>trying to switch a DC source the AC type SSR will turn it on but
>>>
>>>
>>not turn
>>it off.
>>
>>
>>
>>Addresses:
>>FAQ: http://www.ktmarketing.com/faq.html
>>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>>
>>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>>Moderator: pentam@... indigo_red@... [Moderators]
>>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>
>>OFF Topic POSTS: General Machining
>>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
>>http://www.metalworking.com/news_servers.html
>>
>>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>>
>>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>>bill
>>List Mom
>>List Owner
>>
>>
>>
>>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>>
>>
>>
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>Moderator: pentam@... indigo_red@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
>
>

Discussion Thread

Jack Hoffa 2003-11-20 14:26:59 UTC SS Relays Egroupscdh (E-mail) 2003-11-20 15:22:40 UTC RE: [CAD_CAM_EDM_DRO] SS Relays Alan Marconett KM6VV 2003-11-20 15:55:32 UTC Re: [CAD_CAM_EDM_DRO] SS Relays James Cullins 2003-11-20 17:55:46 UTC Re: [CAD_CAM_EDM_DRO] SS Relays mrpootoo 2003-11-21 11:55:06 UTC Re: SS Relays Harvey White 2003-11-21 13:16:28 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays Erie Patsellis 2003-11-21 13:25:02 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays Jon Elson 2003-11-21 20:58:40 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays cutthroatplasmaco 2003-12-12 22:35:21 UTC SS Relays - Revisited Jon Elson 2003-12-12 22:45:49 UTC Re: [CAD_CAM_EDM_DRO] SS Relays - Revisited Bob Muse 2003-12-12 23:29:29 UTC Re: [CAD_CAM_EDM_DRO] SS Relays - Revisited Mark Schaaf 2003-12-13 05:57:51 UTC Re: [CAD_CAM_EDM_DRO] SS Relays - Revisited k1hop 2003-12-13 05:58:00 UTC Re: SS Relays - Revisited turbulatordude 2003-12-13 06:18:00 UTC Re: SS Relays - Revisited Moore 2003-12-13 07:03:59 UTC Re: SS Relays - Revisited cutthroatplasmaco 2003-12-13 18:58:54 UTC Re: SS Relays - Revisited Moore 2003-12-13 21:32:43 UTC Re: SS Relays - Revisited cutthroatplasmaco 2003-12-14 20:55:21 UTC Re: SS Relays - Revisited caudlet 2003-12-15 16:13:54 UTC Re: SS Relays - Revisited Moore 2003-12-15 17:23:10 UTC Re: SS Relays - Revisited cutthroatplasmaco 2003-12-15 21:25:16 UTC Re: SS Relays - Revisited Moore 2003-12-15 21:51:52 UTC Re: SS Relays - Revisited james_cullins@s... 2003-12-15 22:29:59 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays - Revisited Mark Schaaf 2003-12-15 22:30:27 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays - Revisited james_cullins@s... 2003-12-16 05:42:47 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays - Revisited info@t... 2003-12-16 21:06:08 UTC Re: SS Relays - Revisited