CAD CAM EDM DRO - Yahoo Group Archive

Re: SS Relays - Revisited

on 2003-12-13 18:58:54 UTC
> 1. What is the part number of the crydom?
The model # is DC60S3

> 2. What are you using to turn it on?
I'm using a campbelldesigns.com breakout board to trigger the relay -
12VDC

> 3. What is each wire of the crydom hooked to?
so, the +12Vdc from the breakout board is hooked to the positive side
of the input on the relay, the gnd side of the breakout board is
hooked to the other (I guess it would be referred to as gnd) side of
the input on the relay. +18Vdc side of the torch trigger is hooked to
the + side of the relay output. The other side of the torch trigger
is hooked to the other side of the relay output.

I had originally purchased an AC SSR and it worked, wired basically
as I had wired this new crydom (except I wasn't using a breakout
board at that time). The problem with that was when I shut the relay
off, it took up to a few seconds for the torch to shut off. So after
reading those past messages from Jon and others explaining why that
happens, that's when I bought the dc relay... so, I'm fairly sure
that it's wired correctly...

> 4. What is the DC power source for the load you are switching.
Not exactly sure what you mean here?... The Plasma cutter has 18Vdc
on the ttorch trigger...

Thanks,
Chris

Discussion Thread

Jack Hoffa 2003-11-20 14:26:59 UTC SS Relays Egroupscdh (E-mail) 2003-11-20 15:22:40 UTC RE: [CAD_CAM_EDM_DRO] SS Relays Alan Marconett KM6VV 2003-11-20 15:55:32 UTC Re: [CAD_CAM_EDM_DRO] SS Relays James Cullins 2003-11-20 17:55:46 UTC Re: [CAD_CAM_EDM_DRO] SS Relays mrpootoo 2003-11-21 11:55:06 UTC Re: SS Relays Harvey White 2003-11-21 13:16:28 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays Erie Patsellis 2003-11-21 13:25:02 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays Jon Elson 2003-11-21 20:58:40 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays cutthroatplasmaco 2003-12-12 22:35:21 UTC SS Relays - Revisited Jon Elson 2003-12-12 22:45:49 UTC Re: [CAD_CAM_EDM_DRO] SS Relays - Revisited Bob Muse 2003-12-12 23:29:29 UTC Re: [CAD_CAM_EDM_DRO] SS Relays - Revisited Mark Schaaf 2003-12-13 05:57:51 UTC Re: [CAD_CAM_EDM_DRO] SS Relays - Revisited k1hop 2003-12-13 05:58:00 UTC Re: SS Relays - Revisited turbulatordude 2003-12-13 06:18:00 UTC Re: SS Relays - Revisited Moore 2003-12-13 07:03:59 UTC Re: SS Relays - Revisited cutthroatplasmaco 2003-12-13 18:58:54 UTC Re: SS Relays - Revisited Moore 2003-12-13 21:32:43 UTC Re: SS Relays - Revisited cutthroatplasmaco 2003-12-14 20:55:21 UTC Re: SS Relays - Revisited caudlet 2003-12-15 16:13:54 UTC Re: SS Relays - Revisited Moore 2003-12-15 17:23:10 UTC Re: SS Relays - Revisited cutthroatplasmaco 2003-12-15 21:25:16 UTC Re: SS Relays - Revisited Moore 2003-12-15 21:51:52 UTC Re: SS Relays - Revisited james_cullins@s... 2003-12-15 22:29:59 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays - Revisited Mark Schaaf 2003-12-15 22:30:27 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays - Revisited james_cullins@s... 2003-12-16 05:42:47 UTC Re: [CAD_CAM_EDM_DRO] Re: SS Relays - Revisited info@t... 2003-12-16 21:06:08 UTC Re: SS Relays - Revisited