Re: servo board
Posted by
george_barr
on 2003-11-28 23:33:52 UTC
Thanks for replying. My first router/mill will use geckos. In fact,
I already have 3 geckos for step/direction. However, I would like to
eventually move into the more professional stuff like servos. I have
looked at the servotogo, vigproducts.com (cost too much since it
needs more expansion boards), and pico-systems. I am just stuck
between the servotogo and pico-systems. I was told that the
servotogo has an 8 MHZ ISA bus while the pico-sytems uses a fast
parallel port. I was told that the ISA is a much faster
communication bus but I am not sure if that translates into better
performance. To save cost, I'll use brush DC motors using 23 or 34
NEMA motors. What I like about pico-systems is that you can buy the
starter 4-axis kit and then later invest more for the full 8-axis.
However, pico's 8-axis system cost more than servotogo's 8-axis
system. Also, servotogo's says you need a opto-22 product which is
probably another board to hold the relays (more cost). I know that
servotogo is used by many, but pico is fairly new. Pico has more
resolution using 16-bits rather than 13-bits, if it is needed. How
uses/buys the pico system? I would like to hear from users of the
pico servo systems. My future plan for this servo project is to add
a DC motor for the spindle to do tapping, add 4th/5th axis, add lathe
attachments. That is 7-axis already. I can't tell you more since I
am a newbie.
Thanks,
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "industrialhobbies"
<admin@i...> wrote:
I already have 3 geckos for step/direction. However, I would like to
eventually move into the more professional stuff like servos. I have
looked at the servotogo, vigproducts.com (cost too much since it
needs more expansion boards), and pico-systems. I am just stuck
between the servotogo and pico-systems. I was told that the
servotogo has an 8 MHZ ISA bus while the pico-sytems uses a fast
parallel port. I was told that the ISA is a much faster
communication bus but I am not sure if that translates into better
performance. To save cost, I'll use brush DC motors using 23 or 34
NEMA motors. What I like about pico-systems is that you can buy the
starter 4-axis kit and then later invest more for the full 8-axis.
However, pico's 8-axis system cost more than servotogo's 8-axis
system. Also, servotogo's says you need a opto-22 product which is
probably another board to hold the relays (more cost). I know that
servotogo is used by many, but pico is fairly new. Pico has more
resolution using 16-bits rather than 13-bits, if it is needed. How
uses/buys the pico system? I would like to hear from users of the
pico servo systems. My future plan for this servo project is to add
a DC motor for the spindle to do tapping, add 4th/5th axis, add lathe
attachments. That is 7-axis already. I can't tell you more since I
am a newbie.
Thanks,
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "industrialhobbies"
<admin@i...> wrote:
> I just took a quick look at both of the mentioned boards andnoticed
> that the servo amp seems to require the other components (Pico) andI
> didn't see any volt/amp numbers for the other. Which makes mewhich
> question the total price of the application.
>
> I noticed you used the words "cost-effective" in your question,
> leads me to believe this is a hobby application, is this the case?hand
>
> To recommend a controller we would have to know more about your
> application. For example if you were just doing a CNC mill or
> something Geckos are the way to go(my opinion), but on the other
> if you are building a teachable CNC arm or something like that youbrushed
> would need the additional features offered by these products and
> companies.
>
> Also what kind of servo are you talking about? (I'm guessing
> DC) How many volts? Amps (cont)? Amps (peak)? Motor torqueto
> constant?
>
> When it comes to picking a controller (either servo or stepper) all
> these factors come into play it unjust of us to make an opinion
> without these.
>
> So include a pinch more and we (open forum) will probably be able
> give a better opinion.
>
> Thanks
> Aaron Moss
> www.IndustrialHobbies.com
>
>
>
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "george_barr"
> <george_barr@y...> wrote:
> > I am looking for a servo controller. I have looked at www.pico-
> > systems.com and www.servotogo.com controllers. Which of these 2
> > servo controllers is better and why? Is there any other cost-
> > effective servo controllers out there that I should look at?
> >
> > Thanks,
Discussion Thread
george_barr
2003-11-27 23:02:25 UTC
servo board
mikezcnc
2003-11-28 09:48:13 UTC
Re: servo board
cadcracker@l...
2003-11-28 11:23:40 UTC
Re: [CAD_CAM_EDM_DRO] servo board
Tim Goldstein
2003-11-28 11:37:22 UTC
RE: [CAD_CAM_EDM_DRO] Re: servo board
Paul
2003-11-28 12:03:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
Mariss Freimanis
2003-11-28 12:15:17 UTC
Re: servo board
cadcracker@l...
2003-11-28 12:56:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
Tim Goldstein
2003-11-28 13:20:48 UTC
RE: [CAD_CAM_EDM_DRO] Re: servo board
cadcracker@l...
2003-11-28 13:30:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
Kim Lux
2003-11-28 13:34:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: servo board
cadcracker@l...
2003-11-28 13:42:34 UTC
RE: [CAD_CAM_EDM_DRO] Re: servo board
Paul
2003-11-28 13:44:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
Raymond Heckert
2003-11-28 17:12:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
industrialhobbies
2003-11-28 18:24:23 UTC
Re: servo board
Mariss Freimanis
2003-11-28 18:25:21 UTC
Re: servo board
Jon Elson
2003-11-28 22:33:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
Jon Elson
2003-11-28 22:39:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
george_barr
2003-11-28 23:33:52 UTC
Re: servo board
caudlet
2003-11-29 08:47:31 UTC
Re: servo board
industrialhobbies
2003-11-29 09:00:33 UTC
Re: servo board
george_barr
2003-11-29 15:37:20 UTC
Re: servo board
Jon Elson
2003-11-29 22:20:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
turbulatordude
2003-11-30 05:42:13 UTC
Re: servo board - or steppers to start ?
ballendo
2003-11-30 06:28:29 UTC
Re: servo board
caudlet
2003-11-30 08:51:19 UTC
Re: servo board
William Scalione
2003-11-30 11:33:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board - or steppers to start ?
turbulatordude
2003-11-30 14:09:22 UTC
Re: servo board - or steppers to start ?
Raymond Heckert
2003-11-30 16:29:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: servo board
turbulatordude
2003-12-01 04:39:14 UTC
Re: servo board