CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: servo board - or steppers to start ?

on 2003-11-30 11:33:42 UTC
> > I found out that the STG requires a relay board and break-out
> > boards. This can add much to the finaly cost of purchasing a STG to
> > the point that a Pico Systems 8-axis system may cost about the same
> > for a STG system. Right now, I am leaning towards the Pico System.
> > However, the STG cutomer base is plenty and I am not sure how many
> > Pico Systems Servo's have been sold.
> >
> > Thanks,

Hi,

Not sure if you realize this, maybe you do, but I have not seen it mentioned
in your posts (could be I missed it) but you will also need analog servo
amps to drive the motors with either the Pico or Servo To Go setup, whereas
the Gecko servo drives wil take step and direction input and drive the
motors directly.

Bill

Discussion Thread

george_barr 2003-11-27 23:02:25 UTC servo board mikezcnc 2003-11-28 09:48:13 UTC Re: servo board cadcracker@l... 2003-11-28 11:23:40 UTC Re: [CAD_CAM_EDM_DRO] servo board Tim Goldstein 2003-11-28 11:37:22 UTC RE: [CAD_CAM_EDM_DRO] Re: servo board Paul 2003-11-28 12:03:42 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board Mariss Freimanis 2003-11-28 12:15:17 UTC Re: servo board cadcracker@l... 2003-11-28 12:56:39 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board Tim Goldstein 2003-11-28 13:20:48 UTC RE: [CAD_CAM_EDM_DRO] Re: servo board cadcracker@l... 2003-11-28 13:30:31 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board Kim Lux 2003-11-28 13:34:02 UTC RE: [CAD_CAM_EDM_DRO] Re: servo board cadcracker@l... 2003-11-28 13:42:34 UTC RE: [CAD_CAM_EDM_DRO] Re: servo board Paul 2003-11-28 13:44:18 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board Raymond Heckert 2003-11-28 17:12:02 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board industrialhobbies 2003-11-28 18:24:23 UTC Re: servo board Mariss Freimanis 2003-11-28 18:25:21 UTC Re: servo board Jon Elson 2003-11-28 22:33:57 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board Jon Elson 2003-11-28 22:39:19 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board george_barr 2003-11-28 23:33:52 UTC Re: servo board caudlet 2003-11-29 08:47:31 UTC Re: servo board industrialhobbies 2003-11-29 09:00:33 UTC Re: servo board george_barr 2003-11-29 15:37:20 UTC Re: servo board Jon Elson 2003-11-29 22:20:46 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board turbulatordude 2003-11-30 05:42:13 UTC Re: servo board - or steppers to start ? ballendo 2003-11-30 06:28:29 UTC Re: servo board caudlet 2003-11-30 08:51:19 UTC Re: servo board William Scalione 2003-11-30 11:33:42 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board - or steppers to start ? turbulatordude 2003-11-30 14:09:22 UTC Re: servo board - or steppers to start ? Raymond Heckert 2003-11-30 16:29:15 UTC Re: [CAD_CAM_EDM_DRO] Re: servo board turbulatordude 2003-12-01 04:39:14 UTC Re: servo board