Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Posted by
JanRwl@A...
on 2004-01-14 20:02:01 UTC
But servos are NECESSARILY "closed loop" (with shaft-encoders). It is the
STEPPERS that are "open loop"! JRR
[Non-text portions of this message have been removed]
STEPPERS that are "open loop"! JRR
[Non-text portions of this message have been removed]
Discussion Thread
ja_erickson
2004-01-10 17:31:46 UTC
e-stop / limit switch help needed
Robert Campbell
2004-01-10 17:44:01 UTC
Re: [CAD_CAM_EDM_DRO] e-stop / limit switch help needed
ja_erickson
2004-01-10 18:50:13 UTC
Re: e-stop / limit switch help needed
james_cullins@s...
2004-01-10 20:39:37 UTC
Re: [CAD_CAM_EDM_DRO] e-stop / limit switch help needed
Peter Homann
2004-01-14 17:22:26 UTC
Is a reduction drive necessary for servo motors?
JanRwl@A...
2004-01-14 18:50:13 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Bob McKnight
2004-01-14 19:19:08 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Peter Homann
2004-01-14 19:46:30 UTC
RE: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Peter Homann
2004-01-14 19:58:59 UTC
RE: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
JanRwl@A...
2004-01-14 20:02:01 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Peter Homann
2004-01-14 20:25:31 UTC
RE: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Jon Elson
2004-01-14 21:23:25 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Jon Elson
2004-01-14 21:29:46 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
industrialhobbies
2004-01-14 22:07:52 UTC
Re: Is a reduction drive necessary for servo motors?
Bob McKnight
2004-01-15 10:17:39 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Harvey White
2004-01-15 11:03:48 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Jon Elson
2004-01-15 21:37:42 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
Bob McKnight
2004-01-15 21:59:38 UTC
Re: [CAD_CAM_EDM_DRO] Is a reduction drive necessary for servo motors?
ballendo
2004-01-16 09:04:48 UTC
Stepper vs. servo resolution was Re: Is a reduction drive nec
ballendo
2004-01-16 09:09:08 UTC
two types of servos was Re: Is a reduction...
Peter Homann
2004-01-16 16:32:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: Is a reduction drive necessary for servo motors?
Bob McKnight
2004-01-17 07:34:04 UTC
Re: [CAD_CAM_EDM_DRO] two types of servos was Re: Is a reduction...