Re: emc help
Posted by
Greg
on 2004-01-30 17:07:47 UTC
-
Hello,
Whoever wrote this doesnt know much about encoders.
I use hiedhain encoders and they are expensive but they have a max
encoder freq of 300khz which is double the normal spec of most other
encoders.
The only exception to this i have found is laser encoders made by
canon.(Way to expensive)
Also if you check your specs on the STG board the max enoder freq is
not 10 mhz but much lower.
And of course the parallel port could not run at these speed.
And even the pico systems is limited to 300khz
Regards,
Greg
-- In CAD_CAM_EDM_DRO@yahoogroups.com, Ray Henry <rehenry@u...> wrote:
Hello,
Whoever wrote this doesnt know much about encoders.
I use hiedhain encoders and they are expensive but they have a max
encoder freq of 300khz which is double the normal spec of most other
encoders.
The only exception to this i have found is laser encoders made by
canon.(Way to expensive)
Also if you check your specs on the STG board the max enoder freq is
not 10 mhz but much lower.
And of course the parallel port could not run at these speed.
And even the pico systems is limited to 300khz
Regards,
Greg
-- In CAD_CAM_EDM_DRO@yahoogroups.com, Ray Henry <rehenry@u...> wrote:
>1800 to
> > From: Jon Elson <elson@p...>
> <s>
> > Most encoder counters can handle 300,000 to 1 million encoder
> > counts/second. So, that would be 30 to 100 inches a second, or
> > 6000 IPM. Is that enough for you?so you
>
> STG claims 10 MHz.. In theory you can multiply these values by 10
> could be dealing in miles per minute.
>
> Ray
Discussion Thread
Greg
2004-01-28 17:24:22 UTC
emc help
Jon Elson
2004-01-28 21:24:10 UTC
Re: [CAD_CAM_EDM_DRO] emc help
Greg
2004-01-28 22:04:55 UTC
Re: emc help
Jon Elson
2004-01-29 08:37:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc help
Greg
2004-01-29 20:42:08 UTC
Re: emc help
Jon Elson
2004-01-29 21:45:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc help
Greg
2004-01-29 23:29:53 UTC
Re: emc help
Jon Elson
2004-01-30 10:23:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc help
Ray Henry
2004-01-30 11:19:41 UTC
Re: Re: Re: emc help
Greg
2004-01-30 17:01:31 UTC
Re: emc help
Greg
2004-01-30 17:07:47 UTC
Re: emc help
Ray Henry
2004-01-31 08:26:59 UTC
Re: Re: emc help
Greg
2004-01-31 10:48:14 UTC
Re: emc help
Robin Szemeti
2004-01-31 12:31:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc help
Roy J. Tellason
2004-01-31 12:55:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc help
Greg
2004-01-31 16:29:22 UTC
Re: emc help
Greg
2004-01-31 16:36:05 UTC
Re: emc help
Greg
2004-01-31 17:39:35 UTC
Re: emc help
Ray Henry
2004-01-31 18:06:30 UTC
Re: Re: emc help
Dale Emery
2004-01-31 19:43:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: emc help
Jon Elson
2004-01-31 20:47:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: emc help
Greg
2004-01-31 22:12:07 UTC
Re: emc help
Greg
2004-01-31 22:52:16 UTC
Re: emc help