CAD CAM EDM DRO - Yahoo Group Archive

Re: replacing anilam crusader II control

Posted by Jim H
on 2004-02-18 18:50:46 UTC
Roy

Well I can't count! There are 2 lights on the com port tester. Yes
the little unit with the 7 led's. The DR and DSR both glow merrily red.

Thanks
for responding.

Jim.


--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Roy J. Tellason"
<rtellason@b...> wrote:
> On Monday 16 February 2004 12:21 pm, Jim H wrote:
> > Hi
> >
> > Has anyone out there replaced an anilam crusader II control on a
> > knee mill? While my control works well the record and input rs232
> > ports appear dead. A com port tester from radio shack shows no
> > lights when connected to the record port and only one light when
> > connected to the input port.
>
> That the little unit with 7 LEDs and a 25-pin connector on each
side? I have
> one of those, and it's real handy. The trouble is, you don't know
which of
> those pins are used, and which aren't. RS232 is a pretty flexible
spec...
>
> Maybe you could have a look at the board and see? Which light is on?
>
> Odds are that if the port isn't working the way it should, the
chips that
> connect to it are the problem. These are very often 1488 and 1489
(or the
> equivalent 75188 and 75189, same thing). I had some equipment where
Ihad to
> replace these regularly, so I ended up putting sockets in. <g> The
> receiver half of that pair only needs +5v power, but the
transmitter end of
> it needs bipolar supplies, typically +/- 12v. If these aren't
present then
> the port won't work either. The '88 is the transmitter and you
should see
> power on pins 1 (- supply) and 14 (+ supply). The '89 is the
receiver and
> that should show +5 on pin 14. Pin 7 is ground in both cases.
>
> > I had hoped to do more 3 axis work but the limitation on keyboard
> > entry holds me to 2-1/2 axis mostly. A call to anilam gave a price
> > of $7500 for a 3000m replacement control. Just a few thousand out of
> > the budget.
>
> Yow. For that kind of money I'd be trying to fix the one you've
got. How are
> your soldering skills? :-)
>
> > Has anyone tried a home brew replacement?
>
> Not me, but hopefully the above will be of some help.

Discussion Thread

Jim H 2004-02-16 10:52:22 UTC replacing anilam crusader II control Larry Ragan 2004-02-16 11:11:38 UTC RE: [CAD_CAM_EDM_DRO] replacing anilam crusader II control Roy J. Tellason 2004-02-16 12:34:20 UTC Re: [CAD_CAM_EDM_DRO] replacing anilam crusader II control Jim H 2004-02-18 18:50:46 UTC Re: replacing anilam crusader II control Jim H 2004-02-18 18:50:51 UTC Re: replacing anilam crusader II control Roy J. Tellason 2004-02-18 21:14:18 UTC Re: [CAD_CAM_EDM_DRO] Re: replacing anilam crusader II control Larry Ragan 2004-02-19 08:20:02 UTC RE: [CAD_CAM_EDM_DRO] Re: replacing anilam crusader II control Jim H 2004-02-20 18:50:39 UTC Re: replacing anilam crusader II control Roy J. Tellason 2004-02-20 20:45:33 UTC Re: [CAD_CAM_EDM_DRO] Re: replacing anilam crusader II control Jim H 2004-02-22 22:00:59 UTC Re: replacing anilam crusader II control Roy J. Tellason 2004-02-23 11:13:49 UTC Re: [CAD_CAM_EDM_DRO] Re: replacing anilam crusader II control metlmunchr 2004-02-23 11:58:27 UTC Re: replacing anilam crusader II control Jim H 2004-02-24 07:13:50 UTC Re: replacing anilam crusader II control Jim H 2004-02-25 07:46:23 UTC Re: replacing anilam crusader II control Harvey White 2004-02-25 08:48:45 UTC Re: [CAD_CAM_EDM_DRO] Re: replacing anilam crusader II control metlmunchr 2004-02-25 13:29:58 UTC Re: replacing anilam crusader II control