Re: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
Posted by
cnc002@a...
on 2004-05-02 18:19:11 UTC
In a message dated 5/2/2004 8:44:40 PM Eastern Daylight Time,
sstephenssprint020@... writes:
I'm running CNC and I'd like to work as accurately as
possible. Figure I'll get all the methods people are using and figure out
which works best for me.
The best way to find an accurate zero is to do what several say and either
with the spindle running or not running, move the Z axis until the cutter JUST
touches the top of either the base table or a scrap piece of material of the
same thickness as that you are going to machine. Then you tell the Z to go down
say 0.1250" or even 0.0625" and make a test cut on the scrap material. Then
you measure the depth of the actual cut. You can then go into the machine
parameters of the controller and adjust the Z value so that when you tell it to
go into the material a certain amount, it goes into it that amount. If you are
not concerned with accuracy in the thousandths of an inch range then the
"touch and go" method some describe is good enough
Randy Abernathy
4626 Old Stilesboro Road NW
Acworth, GA 30101-4066
Phone / Fax: 770-974-5295
Mobile: 678-772-4113
E-mail: cnc002@...
I furnish technical support, repair, and other related services for your
industrial woodworking machinery. My background as Senior Service Engineer for the
SCMI Group for nearly fifteen years with factory training, combines with my
extensive background in electronics, mechanics, pneumatics, electrical and CNC
machinery to offer you needed support for your machinery.
[Non-text portions of this message have been removed]
sstephenssprint020@... writes:
I'm running CNC and I'd like to work as accurately as
possible. Figure I'll get all the methods people are using and figure out
which works best for me.
The best way to find an accurate zero is to do what several say and either
with the spindle running or not running, move the Z axis until the cutter JUST
touches the top of either the base table or a scrap piece of material of the
same thickness as that you are going to machine. Then you tell the Z to go down
say 0.1250" or even 0.0625" and make a test cut on the scrap material. Then
you measure the depth of the actual cut. You can then go into the machine
parameters of the controller and adjust the Z value so that when you tell it to
go into the material a certain amount, it goes into it that amount. If you are
not concerned with accuracy in the thousandths of an inch range then the
"touch and go" method some describe is good enough
Randy Abernathy
4626 Old Stilesboro Road NW
Acworth, GA 30101-4066
Phone / Fax: 770-974-5295
Mobile: 678-772-4113
E-mail: cnc002@...
I furnish technical support, repair, and other related services for your
industrial woodworking machinery. My background as Senior Service Engineer for the
SCMI Group for nearly fifteen years with factory training, combines with my
extensive background in electronics, mechanics, pneumatics, electrical and CNC
machinery to offer you needed support for your machinery.
[Non-text portions of this message have been removed]
Discussion Thread
peterboutakis
2004-05-02 07:29:04 UTC
Busy Bee retrofit ?
shyningnight@y...
2004-05-02 14:50:21 UTC
Re: Busy Bee retrofit ?
Scott A. Stephens
2004-05-02 15:51:55 UTC
Finding Z zero for CNC
Greg Nuspel
2004-05-02 16:00:12 UTC
Re: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
Art Eckstein
2004-05-02 16:48:10 UTC
Re: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
Scott Ellis
2004-05-02 17:13:42 UTC
Re: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
Doug Chartier
2004-05-02 17:15:08 UTC
Re: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
Scott A. Stephens
2004-05-02 17:43:01 UTC
Re: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
cnc002@a...
2004-05-02 18:19:11 UTC
Re: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
marvinstovall
2004-05-02 19:10:33 UTC
Re: Finding Z zero for CNC
Jon Elson
2004-05-02 22:35:58 UTC
Re: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
peterboutakis
2004-05-02 23:56:16 UTC
Re: Busy Bee retrofit ?
shyningnight@y...
2004-05-03 07:14:02 UTC
Re: Busy Bee retrofit ?
metlmunchr
2004-05-03 07:16:12 UTC
Re: Finding Z zero for CNC
jess@p...
2004-05-03 08:06:33 UTC
Re: [CAD_CAM_EDM_DRO] Busy Bee retrofit ?
ballendo
2004-05-03 08:53:52 UTC
Re: Finding Z zero for CNC
Peter Renolds
2004-05-03 09:11:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Busy Bee retrofit ?
RichD
2004-05-03 09:44:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Finding Z zero for CNC
Pat Bearss
2004-05-03 11:39:20 UTC
Re: Busy Bee retrofit ?Bridgeport Series 1 CNC
peterboutakis
2004-05-03 13:59:24 UTC
Re: Busy Bee retrofit ?
peterboutakis
2004-05-03 14:28:35 UTC
Busy Bee retrofit ?
vavaroutsos
2004-05-03 16:19:17 UTC
Re: Busy Bee retrofit ?
Hugh Prescott
2004-05-03 17:51:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Busy Bee retrofit ?
Greg Nuspel
2004-05-03 19:51:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Finding Z zero for CNC
cnc002@a...
2004-05-03 20:42:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Finding Z zero for CNC
Greg Nuspel
2004-05-04 03:53:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Finding Z zero for CNC
treadlemill
2004-05-04 07:03:56 UTC
Re: Busy Bee retrofit ?
mayfieldtm
2004-05-04 07:44:00 UTC
Re: Busy Bee retrofit ?
Adrian Teo
2004-05-04 08:31:53 UTC
RE: [CAD_CAM_EDM_DRO] Finding Z zero for CNC
peterboutakis
2004-05-05 00:00:37 UTC
Re: Busy Bee retrofit ?
wthomas@g...
2004-05-05 20:42:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Busy Bee retrofit ?