Re: [CAD_CAM_EDM_DRO] Re: Need a vacuum system for acrylic sheets
Posted by
Bob Muse
on 2005-01-12 05:56:13 UTC
If you are talking about compressed air venturi pumps--they work and they
will generate a good vacuum but they use a lot of air. How much surface
area is the vacuum acting on? How is the vacuum piping done?
will generate a good vacuum but they use a lot of air. How much surface
area is the vacuum acting on? How is the vacuum piping done?
----- Original Message -----
From: "kdoney_63021" <kdoney_63021@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, January 12, 2005 5:47 AM
Subject: [CAD_CAM_EDM_DRO] Re: Need a vacuum system for acrylic sheets
>
>
> Sorry, I should have been a little more specific.
>
> I'm actually not cutting the 1/8" acrylic plastic sheet. I am
> painting on it with dispensing valves and acrylic paint. I need to
> hold the sheet flat (+- .1") against the surface of the table. The
> sheets, as they come off the properly constructed storage racks, are
> sometimes off by .5" by warping. I don't need high volume, except to
> counteract the table leakage and I don't need high vacuum since I
> only have 12 of the 1/4" bullet catches which allow the vacuum to
> form inside of my multiple areas of
> "Poron Quick Recovery Foam Strip, 1/8" Thick X 1/2" Wide".
>
> I was thinking that this rubber was the wrong type, causing massive
> leaks when I tried my new Gast vacuum pump but when I put my finger
> over the vacuum inlet it didn't seem that strong so I assumed the
> pump was the problem.
>
> I then tried the wet dry vac and got no better result. Maybe my
>
> "Bullet-Style Spring-Loaded Catch, Nonadjustable Mortise-Mount
> Strike, 1/4"D X 3/8"L"
>
> were too small to allow the vacuum to hold the piece?
>
> Should I just remove the catches and cover the unused holes?
>
> I've heard good things about venturi pumps. Any comments?
>
> Kevin
>
>
>
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Robert Campbell" <bob@c...>
> wrote:
> > Kevin,
> >
> > what are the size of the parts? How many of the same parts would
> you be
> > cutting?
> >
> > What type material are you cutting?
> >
> > Basically you have two types of vacuum systems. One is the high
> vacuum low
> > flow system and the other is the high flow lower vacuum. For the
> high flow
> > system the vacuum should be around 15".
> >
> (snip)
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
Discussion Thread
kdoney_63021
2005-01-11 18:58:08 UTC
Need a vacuum system for acrylic sheets
Ron
2005-01-11 19:23:42 UTC
Re: Need a vacuum system for acrylic sheets
Robert Campbell
2005-01-11 19:48:18 UTC
Re: [CAD_CAM_EDM_DRO] Need a vacuum system for acrylic sheets
Bob Muse
2005-01-11 20:09:20 UTC
Re: [CAD_CAM_EDM_DRO] Need a vacuum system for acrylic sheets
turbulatordude
2005-01-11 20:33:29 UTC
Re: Need a vacuum system for acrylic sheets
kdoney_63021
2005-01-12 05:47:44 UTC
Re: Need a vacuum system for acrylic sheets
Bob Muse
2005-01-12 05:56:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need a vacuum system for acrylic sheets
Leslie Watts
2005-01-12 06:03:58 UTC
RE: [CAD_CAM_EDM_DRO] Re: Need a vacuum system for acrylic sheets
Stephan Kotze
2005-01-12 07:11:54 UTC
RE:Need a vacuum system for acrylic sheets
turbulatordude
2005-01-12 07:55:49 UTC
Re: Need a vacuum system for acrylic sheets
Robert Campbell
2005-01-12 12:18:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need a vacuum system for acrylic sheets
JanRwl@A...
2005-01-12 14:10:17 UTC
Re: [CAD_CAM_EDM_DRO] RE:Need a vacuum system for acrylic sheets
James Lewis
2005-01-14 21:19:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Need a vacuum system for acrylic sheets