Re: [CAD_CAM_EDM_DRO] upgrade
Posted by
Scott L Golden
on 2005-01-22 17:05:10 UTC
Ahhhh..... starting to see the light.
lol
Scott L Golden
Never Give Up
lol
Scott L Golden
Never Give Up
----- Original Message -----
From: "Jonathan Stark" <cadcam@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Friday, January 21, 2005 11:42 PM
Subject: Re: [CAD_CAM_EDM_DRO] upgrade
>
>
> Hi Scott,
>
> Quoting Scott L Golden (escowizard@...):
> > I think I have a M3 firmware bandit with RS232 hookup
>
> Cool. That suggests you actually got yours to start up! :)
>
> > Now you will have to go a little slow for me on the "quadrature output "
> > stuff. I'm not stupid but this end of things are not the easiest to
grasp.
>
> The stepper motors connected to my Bandit I have 4 phases (ABCD). The
> stepper motor 'steps' by having one (or more) of these phases energized.
> When they are energized, the motor 'steps' to align it's magnetic field
> with the energized coil(s).
>
> You can make your stepper motor move by energizing the phases in order.
> For single stepping, it might look like this:
>
> A B C D
> X - - -
> - X - -
> - - X -
> - - - X
>
> Backwards would be just the opposite;
>
> A B C D
> - - - X
> - - X -
> - X - -
> X - - -
>
> When you control the 4 phases independently, I've seen that called
> 'quadrature' inputs/outputs. In this case, it takes 4 signals.
>
> In the most common configuration I've seen for gecko drives, the gecko
> drive takes a step and direction input. When you send a 'step'
> signal to the gecko, it knows which coil(s) are energized now, and
> which coil(s) need to be turned on/off to move one step (or
> microstep) in the direction you gave it with the 'step' input.
> This only takes 2 inputs (step and direction) instead of 4.
>
> EMC can be configured to generate the 4 outputs you need above directly.
> All you need to do is wire your parallel port on your PC appropriately
> to the 16 pin ribbon cables in your bandit case, and assuming your
> bandit's drives work, EMC will drive your bridgeport with your existing
> drives. No capital investment required! :)
>
> EMC, Mach1/2/3, TurboCNC, and others can also be configured to
> work in the step/direction mode that gecko uses.
>
> Clear as mud? :)
>
> Jonathan
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
[Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
Discussion Thread
bbrreid2000
2004-04-07 19:11:17 UTC
upgrade
Scott L Golden
2005-01-21 18:44:45 UTC
upgrade
Jonathan Stark
2005-01-21 19:44:10 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
Scott L Golden
2005-01-21 20:10:35 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
R Rogers
2005-01-21 20:21:53 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
R Rogers
2005-01-21 20:54:16 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
braidmeister
2005-01-21 21:01:53 UTC
Re: upgrade
Jonathan Stark
2005-01-21 22:20:16 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
cnc_4_me
2005-01-22 05:42:42 UTC
Re: upgrade
turbulatordude
2005-01-22 05:53:43 UTC
Re: upgrade
cnc_4_me
2005-01-22 10:39:41 UTC
Re: upgrade
Jon Elson
2005-01-22 11:19:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: upgrade
turbulatordude
2005-01-22 11:37:49 UTC
Re: upgrade
cnc_4_me
2005-01-22 14:43:34 UTC
Re: upgrade
cnc_4_me
2005-01-22 14:47:26 UTC
Re: upgrade
Polaraligned
2005-01-22 16:01:42 UTC
Re: upgrade
Scott L Golden
2005-01-22 17:05:10 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
Scott L Golden
2005-01-22 17:09:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: upgrade
John Delaney
2005-01-22 20:04:19 UTC
Re: upgrade
Mike Pfleger
2005-01-22 21:40:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: upgrade
Rod McBeath
2005-01-22 21:56:50 UTC
Re: upgrade
arturodu
2005-01-23 16:03:16 UTC
Re: upgrade
Scott L Golden
2005-01-25 10:28:41 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
Jonathan Stark
2005-01-25 12:30:34 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
Scott L Golden
2005-01-25 12:51:30 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
Jonathan Stark
2005-01-25 13:23:51 UTC
Re: [CAD_CAM_EDM_DRO] upgrade
Torsten
2005-01-25 13:40:52 UTC
Re: upgrade