Re: [CAD_CAM_EDM_DRO] Formula
Posted by
Stephen Wille Padnos
on 2005-02-16 08:45:30 UTC
Bruce Pigeon wrote:
"convert" between them. The peak ratings are usually 4-5 times the
continuous, so if you have a peak value only, divide by 5 to get the
(conservative) continuous rating.
Other than that, one foot pound is easy to convert to ounce inches:
convert feet to inches by multiplying by 12 (12 inches per foot),
convert pounds to ounces by multiplying by 16 (16 ounces per pound). So,
one foot-pound is 12*16 or 192 ounce-inches.
- Steve
>HiFirst off, peak and continuous ratings are different - you can't
>
>Is there a formula to determine what the oz in of a motor is from the
>continuous stall lb/ft or peak
>stall lb/ft. Is there a web site I can go to go reference this material. I
>know little about motors and
>controls. Any help would be appreciated.
>
>Bruce
>
>
"convert" between them. The peak ratings are usually 4-5 times the
continuous, so if you have a peak value only, divide by 5 to get the
(conservative) continuous rating.
Other than that, one foot pound is easy to convert to ounce inches:
convert feet to inches by multiplying by 12 (12 inches per foot),
convert pounds to ounces by multiplying by 16 (16 ounces per pound). So,
one foot-pound is 12*16 or 192 ounce-inches.
- Steve
Discussion Thread
Bruce Pigeon
2005-02-16 08:29:09 UTC
Formula
Stephen Wille Padnos
2005-02-16 08:45:30 UTC
Re: [CAD_CAM_EDM_DRO] Formula
R Rogers
2005-02-16 08:51:48 UTC
Re: [CAD_CAM_EDM_DRO] Formula
Bruce Pigeon
2005-02-16 09:18:21 UTC
Re: [CAD_CAM_EDM_DRO] Formula
Stephen Wille Padnos
2005-02-16 09:26:04 UTC
Re: [CAD_CAM_EDM_DRO] Formula
Bruce Pigeon
2005-02-16 09:41:26 UTC
Re: [CAD_CAM_EDM_DRO] Formula
Bruce Pigeon
2005-02-16 09:50:51 UTC
Re: [CAD_CAM_EDM_DRO] Formula
Andy Wander
2005-02-16 09:51:23 UTC
RE: [CAD_CAM_EDM_DRO] Formula
Bruce Pigeon
2005-02-16 10:07:12 UTC
Re: [CAD_CAM_EDM_DRO] Formula
Bruce Pigeon
2005-02-16 10:07:19 UTC
RE: [CAD_CAM_EDM_DRO] Formula
Stephen Wille Padnos
2005-02-16 10:12:32 UTC
Re: [CAD_CAM_EDM_DRO] Formula
Andy Wander
2005-02-16 10:16:16 UTC
RE: [CAD_CAM_EDM_DRO] Formula
Jens Swales
2005-02-16 10:20:54 UTC
Re: Formula/Calculating Tool
Maxi Bertotto
2005-02-16 12:34:01 UTC
.STL files - Question
Robert Campbell
2005-02-16 12:48:29 UTC
Re: [CAD_CAM_EDM_DRO] .STL files - Question
Bruce Pigeon
2005-02-16 14:33:31 UTC
Re: [CAD_CAM_EDM_DRO] Formula
MateuszGoÿffffb3ÿffffb9bek
2005-02-26 09:36:05 UTC
Re: [CAD_CAM_EDM_DRO] .STL files - Question