Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
Posted by
Tom Hubin
on 2005-08-19 08:27:36 UTC
Hello Jim,
mill. You should be able to measure from reference sides to the holes
and slots and determine where the errors are?
Are the slots parallel to each other but offset 1/8 inch or are they not
parallel so that opposite ends are offset 1/8 inch in opposite
directions?
What size dowel pin holes (diameter and depth)? What coordinates?
What size endmill bit? What size slot (width, depth, length)? What size
cuts (sideways and depth) and feedrate?
What material?
Can you provide drawing and gcode if somebody wants to check these for
you?
Tom Hubin
thubin@...
> When I put the two halves together, the index holes line up properlyEach might be off by 1/16 inch. Even so, this is a huge error on a CNC
> but the two milled slots are slightly skewed from each other (approx.
> 1/8" over 4" of travel).
mill. You should be able to measure from reference sides to the holes
and slots and determine where the errors are?
Are the slots parallel to each other but offset 1/8 inch or are they not
parallel so that opposite ends are offset 1/8 inch in opposite
directions?
What size dowel pin holes (diameter and depth)? What coordinates?
What size endmill bit? What size slot (width, depth, length)? What size
cuts (sideways and depth) and feedrate?
What material?
Can you provide drawing and gcode if somebody wants to check these for
you?
Tom Hubin
thubin@...
Discussion Thread
kaptainkarst
2005-08-19 00:09:31 UTC
Newbie: Two halves of simple die not aligning properly - Long
Marcus
2005-08-19 07:47:00 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
Tom Hubin
2005-08-19 08:27:36 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
Russ Waters
2005-08-19 09:04:06 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves not aligning properly - Did you mirror......
Jon Elson
2005-08-19 09:53:01 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
kaptainkarst
2005-08-19 15:33:14 UTC
Re: Newbie: Two halves not aligning properly : part 2...long again
ringleboy26
2005-08-19 16:21:48 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-19 19:08:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves not aligning properly : part 2...long again
kaptainkarst
2005-08-19 19:09:10 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Tom Hubin
2005-08-19 22:54:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
kaptainkarst
2005-08-20 07:22:17 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-20 11:09:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-20 11:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
John Johnson
2005-08-24 06:26:41 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long