Re: Newbie: Two halves of simple die not aligning properly - Long
Posted by
kaptainkarst
on 2005-08-20 07:22:17 UTC
Hi Tim,
The three hole (now this is in wood remember) at .375" using wooden
dowle pins (this is for my learning/testing only at this time).
Here is the code for Half A:
The holes are here:
Part 1:
1A: X1.2418 Y0.5143
1B: X0.5199 Y2.3662
1C: X3.4032 Y2.5274
Part 2:
2A: X2.7582 Y0.5143
2B: X3.4801 Y2.3662
2C: X0.5968 Y2.5274
These seem to work just fine.
I have found the error(s) and I need to go through the proceedures of
aligning the table. I have found several postings on the Shoptask
Forums on how to do this.
This will give me something to do in the hot garage today....
Thanks for all of the input!
Jim
The three hole (now this is in wood remember) at .375" using wooden
dowle pins (this is for my learning/testing only at this time).
Here is the code for Half A:
The holes are here:
Part 1:
1A: X1.2418 Y0.5143
1B: X0.5199 Y2.3662
1C: X3.4032 Y2.5274
Part 2:
2A: X2.7582 Y0.5143
2B: X3.4801 Y2.3662
2C: X0.5968 Y2.5274
These seem to work just fine.
I have found the error(s) and I need to go through the proceedures of
aligning the table. I have found several postings on the Shoptask
Forums on how to do this.
This will give me something to do in the hot garage today....
Thanks for all of the input!
Jim
Discussion Thread
kaptainkarst
2005-08-19 00:09:31 UTC
Newbie: Two halves of simple die not aligning properly - Long
Marcus
2005-08-19 07:47:00 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
Tom Hubin
2005-08-19 08:27:36 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
Russ Waters
2005-08-19 09:04:06 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves not aligning properly - Did you mirror......
Jon Elson
2005-08-19 09:53:01 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
kaptainkarst
2005-08-19 15:33:14 UTC
Re: Newbie: Two halves not aligning properly : part 2...long again
ringleboy26
2005-08-19 16:21:48 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-19 19:08:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves not aligning properly : part 2...long again
kaptainkarst
2005-08-19 19:09:10 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Tom Hubin
2005-08-19 22:54:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
kaptainkarst
2005-08-20 07:22:17 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-20 11:09:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-20 11:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
John Johnson
2005-08-24 06:26:41 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long