Re: [CAD_CAM_EDM_DRO] Newbie: Two halves not aligning properly - Did you mirror......
Posted by
Russ Waters
on 2005-08-19 09:04:06 UTC
Hi, not use what your trying to do here, but when I need to align two parts I make sure I "mirror" the parts, this will make sure all will match up..... just a thought.
Russ
Tom Hubin <thubin@...> wrote:
Hello Jim,
mill. You should be able to measure from reference sides to the holes
and slots and determine where the errors are?
Are the slots parallel to each other but offset 1/8 inch or are they not
parallel so that opposite ends are offset 1/8 inch in opposite
directions?
What size dowel pin holes (diameter and depth)? What coordinates?
What size endmill bit? What size slot (width, depth, length)? What size
cuts (sideways and depth) and feedrate?
What material?
Can you provide drawing and gcode if somebody wants to check these for
you?
Tom Hubin
thubin@...
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
---------------------------------
Start your day with Yahoo! - make it your home page
[Non-text portions of this message have been removed]
Russ
Tom Hubin <thubin@...> wrote:
Hello Jim,
> When I put the two halves together, the index holes line up properlyEach might be off by 1/16 inch. Even so, this is a huge error on a CNC
> but the two milled slots are slightly skewed from each other (approx.
> 1/8" over 4" of travel).
mill. You should be able to measure from reference sides to the holes
and slots and determine where the errors are?
Are the slots parallel to each other but offset 1/8 inch or are they not
parallel so that opposite ends are offset 1/8 inch in opposite
directions?
What size dowel pin holes (diameter and depth)? What coordinates?
What size endmill bit? What size slot (width, depth, length)? What size
cuts (sideways and depth) and feedrate?
What material?
Can you provide drawing and gcode if somebody wants to check these for
you?
Tom Hubin
thubin@...
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
---------------------------------
Start your day with Yahoo! - make it your home page
[Non-text portions of this message have been removed]
Discussion Thread
kaptainkarst
2005-08-19 00:09:31 UTC
Newbie: Two halves of simple die not aligning properly - Long
Marcus
2005-08-19 07:47:00 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
Tom Hubin
2005-08-19 08:27:36 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
Russ Waters
2005-08-19 09:04:06 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves not aligning properly - Did you mirror......
Jon Elson
2005-08-19 09:53:01 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long
kaptainkarst
2005-08-19 15:33:14 UTC
Re: Newbie: Two halves not aligning properly : part 2...long again
ringleboy26
2005-08-19 16:21:48 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-19 19:08:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves not aligning properly : part 2...long again
kaptainkarst
2005-08-19 19:09:10 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Tom Hubin
2005-08-19 22:54:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
kaptainkarst
2005-08-20 07:22:17 UTC
Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-20 11:09:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
Jon Elson
2005-08-20 11:20:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Newbie: Two halves of simple die not aligning properly - Long
John Johnson
2005-08-24 06:26:41 UTC
Re: [CAD_CAM_EDM_DRO] Newbie: Two halves of simple die not aligning properly - Long