Re: [CAD_CAM_EDM_DRO] When[emc]
Posted by
Spehro Pefhany
on 2000-06-25 10:58:56 UTC
At 01:47 PM 6/25/00 EDT, you wrote:
There's some people here developing a Linux distribution, maybe I should
ask them about it.
Best regards,
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
Spehro Pefhany --"it's the network..." "The Journey is the reward"
speff@... Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
Contributions invited->The AVR-gcc FAQ is at: http://www.bluecollarlinux.com
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
>This is a great idea. I think part of the mission statement for NIST-EMC isEMC.
>to make the technology available for the hobbyist and small-medium size
>company. The difficulty in setup is a serious barrier - most of the
>toolmakers I work with are barely making it with Win98, forget about Linux!
>Would the CD contain a full image of the operating system and maybe a boot
>disc with a macro to format and partition then copy the CD image to the hard
>drive. In my humble opinion, RTLinux was more of a pain to set up than
>If I had more knowledge about Linux, I would contribute, but I'm justYes, what would it take to make it as easy to install as RH6.0 or 6.2?
>reaching the dangerous stage myself (I know just enough to get me into
>trouble and not enough to get me out of it). Anyway, it's just a thought...
There's some people here developing a Linux distribution, maybe I should
ask them about it.
Best regards,
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
Spehro Pefhany --"it's the network..." "The Journey is the reward"
speff@... Info for manufacturers: http://www.trexon.com
Embedded software/hardware/analog Info for designers: http://www.speff.com
Contributions invited->The AVR-gcc FAQ is at: http://www.bluecollarlinux.com
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
Discussion Thread
Derek B.
2000-06-24 10:24:12 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Jon Anderson
2000-06-24 12:08:52 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
wanliker@a...
2000-06-24 12:09:25 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Steve Carlisle
2000-06-24 12:36:21 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Rich
2000-06-24 13:45:03 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Carey L. Culpepper
2000-06-24 13:47:58 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
petermic@p...
2000-06-24 15:37:46 UTC
Re: When[emc]
Derek B.
2000-06-24 15:38:49 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Jeff Rossel
2000-06-24 16:46:51 UTC
Re: When[emc]
James Cullins
2000-06-24 17:30:40 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Andrew Kozlowski
2000-06-25 05:47:38 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
james owens
2000-06-25 08:33:09 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Peter Smith
2000-06-25 09:47:26 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
johndroc@a...
2000-06-25 10:47:58 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Spehro Pefhany
2000-06-25 10:58:56 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Roland Friestad
2000-06-25 12:57:53 UTC
Re: Re: When[emc]
Alan Marconett KM6VV
2000-06-25 13:53:10 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]
Wayde Gutman
2000-07-01 13:18:41 UTC
Re: [CAD_CAM_EDM_DRO] When[emc]